Question about 2008 Hyundai Elantra

Open Question

Wheel bearing noise on a 2008 hyundai elantra

Is this a common occurance with wheel bearings going bad with 60,000 miles

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
justuscc
  • 360 Answers

SOURCE: Bad front wheel bearing on 1998 Hyundai Elantra

wheel bearing could sieze how loud is it? can you hear it in the car with the windows down? also jack the car up and wiggle the tire any movement? grab the top and the bottom pull and push diffrent ways any clunk or looseness if not you might be ok for a while once it gets loose or real bad clunk replace it hope this helps please leave good feedback thanks

Posted on Sep 18, 2008

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

  • 11 Answers

SOURCE: front wheel bearings

your going to need a press to press the old bearings out and the new ones in i recomend you take it to a shop if you dont have one

Posted on Feb 06, 2009

emissionwiz
  • 76846 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2013 elantra is making a thumping noise when I drive it. the faster I go the louder it gets. but when I turn the wheel to go around curves, the noise stops. any ideas


something is rubbing underneath by tires or maybe a bad axle or ball joint or wheel bearing,could even be a stuck caliper,you will have to look at your tires on backside to check your ball joints,

Sep 26, 2014 | 2013 Hyundai Elantra GLS

1 Answer

I have an 04 hyundai elantra. When im driving slow (0-40mph) you can hear a grinding noise coming from the front driver side, but when i speed up on the highway or anything there is no more noise. it


This could be the brake pads dragging or it could be a wheel bearing. You can check one or the other. The wheel bearing is tested by jacking up the car with that wheel off the ground and see if you can rock the wheel side to side or up and down. The way to check the brakes is to take the wheel off and look at the brake pads.

Sep 14, 2014 | 2004 Hyundai Elantra

1 Answer

Jerking brakes


have the disc rotors checked for warpage and bad wear. Check that the wheel bearings are in good condition and properly adjusted. Check pad thickness as you may have metal on metal.

Apr 03, 2014 | 2008 Hyundai Elantra

1 Answer

I have had 3 wheel bearings in my car and they keep going out - the last one was just put in today and my car is making a very loud noise when I drive - what would be causing the wheel bearings to go out...


Had the noise ever gone away after replacing the wheel bearing? Is it possible it's not a bad wheel bearing, but a bad tire? Or maybe it's a different tires wheel bearing? While i don't have the specs infront of me the axle nut is usually over 150 ft lbs.

Jun 25, 2010 | 2004 Hyundai Elantra

1 Answer

"Humming" or "bearing" type noise in left front at highway speeds


That's a hub bearing. Replace the one that's doing it. I'm assuming this 'roar' is coming from the front, NOT the rear.

Jun 10, 2009 | 2001 Hyundai Elantra

1 Answer

Bad front wheel bearing on 1998 Hyundai Elantra


wheel bearing could sieze how loud is it? can you hear it in the car with the windows down? also jack the car up and wiggle the tire any movement? grab the top and the bottom pull and push diffrent ways any clunk or looseness if not you might be ok for a while once it gets loose or real bad clunk replace it hope this helps please leave good feedback thanks

Sep 18, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...