Question about Cars & Trucks

Open Question

Dash brake light reset for 2006 nissan altima

Dash brake light on how do i get it off already changed brake pads

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dsacco86
  • 1077 Answers

SOURCE: replacing front brake pads on 2002 Nissan Altima

It would be to hard to tell and show you over the computer.
The best and easiest way for you is to buy a Chilton manual for your car at the autoparts store. The book runs about $20
This book is a do-it-yourself bible. It will show you everything you need to know on how to do maintenance and repair on your vehicle.

Posted on Apr 10, 2009

Ad
  • 139 Answers

SOURCE: dashboard warning brake light stays on continuosly nissan altima

Try this, Since you are applying the hand brake. Manually pull up on the emergency pedal and see if the light goes out. If this does work then you could have one of several problems. but, I am thinking that you might be able to adjust the brake tensioner if this car has one.

Posted on Jul 05, 2009

Murphybanton
  • 2004 Answers

SOURCE: recently changed all four rotors and brake pads on

It will normalise after a while.

Good luck and rate this.

Posted on Jul 11, 2009

youredone82
  • 426 Answers

SOURCE: how do I RESET BRAKE LIGHT ON 2006 BMW 325I.Brake

that has to be done by a dealership with a BMW specifiic scan tool

Posted on Oct 30, 2009

  • 1 Answer

SOURCE: How do I change brake light bulb on 2005 Nissan Altima

The first objective is to figure out which bulb you need. I had to replace the bulb for the largest light which was a Sylvania 3157. The next objective is to remove the dang plastic carpet holder/net clip. Recognize that it is a two part piece. Use a flathead screwdriver for leverage. Pry the cap off by levering the screwdriver in the slot on the holder. Then go behind the carpet and pinch the plastic pin still holding the holder in place. Next,pry off the while plastic pieces from the two bolt/nuts you'll need to remove (see manual). Remove the nuts and give the two screws a push from the inside so you can see how the whole light casing comes off. Pry it off from the outside. On the backside of the bulb holder, turn bulb base counterclockwise and gently remove. Pull bulb upward and replace. Do not touch glass on new bulb with your fingers (wear non-powdered rubber gloves). Make sure the bulb snaps in place. Follow these instructions in reverse. Smile, you just learned something new and saved yourself some easy money.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Popping noise in front driver side changed brake pads,caliper caliper bracket pins and clips.help


that would probably be the cv axle joint ..... would be my 1st .

wheel bearing / hub assembly would be my 2nd...

Jul 10, 2014 | 2006 Nissan Altima

1 Answer

How many sensors does 2006 nissan altima front brake pads have.( 1 or 2 )?


Hi Embrel,here's a link to brake pads that go to your Nissan,they have 2 sets,one has one sensor,other has 2 sensors,when you replace,you will see how many they have if no one has changed them before.

Jan 30, 2014 | 2006 Nissan Altima 2.5

1 Answer

My instrument panel does not light up when the lights are turned on 2006 nissan altima


I'm not shore about the 2006 but have you checked your tail lights as Ive found that if there's a glob out on some cars then your dash lights dont work. it maybe a fuse or is the dimmer switch turned down. try these 3 things I hope this helps

Feb 08, 2013 | 2006 Nissan Altima

1 Answer

How to locate and replace brake light switch in a 2006 nissan altima


Your brake light switch is just above brake pedal, under dash. It's small plastic switch w/a couple of wires coming from it. Pretty easy fix.

Mar 08, 2011 | Nissan Altima Cars & Trucks

1 Answer

Brake pad wear indicator light does not go off at the dash after changing rotors brake pads and the sensor in the front wheels all pads and rotors and the sensor is ok at rear. the vehicle has only 30000...


Did you change the sensor? if you did, do a battery reset (disconnect for 10 to 20 min.).

Obviously the wear sensor has made contact with the rotor and is already damaged. You're not even suppose to resuse the wear pad sensor if its worn or damaged anyways.The way how the sensor works is that it must make contact to the rotor to complete the wear pad light indicator circuit. There is no mentioning that he replaced the the wear pad sensor with a new one.

But if one did replaced the wear pad sensor and the wear pad indicator is lit up, the way to reset it is to leave the key on in ignition switch #2 or #1 for about 30sec. turn it off and its reset.

Its possible that you forgot to replace the brake light sensors. They are about 15 bucks, and have to be replaced in order for that light to turn off. You can either get them from the dealer where they'll likely charge you 3 times as much, or you can go to http://www.turnermotorsport.com and get them there.

You have to reset the light by leaving the ignition switch on position #2 for about 30 sec. turn off the ignition and start the engine up and see if it goes out. I recommend buying a new wear pad sensor as well because now light will lit up when you're way below spec (less than 3mm)

Also, you could try with this procedure for one E39: Turning off the Check Brake Linings warning on the Instrument Cluster...
- so you've just changed the brake pads on your E39, along with the wear sensors. The old sensor(s) needed replacement cause you waited a bit too long before changing the pads, and wore through the sensor(s), turning on the BRAKE light on the dash. But wait, the light is still on? But there's a new sensor installed... what gives?!
- there is a procedure required in order to turn off the light/warning. With the ignition off, step on and hold the brake pedal. Now, while holding the brake pedal down, turn on the ignition switch to position 2 (just before cranking). Hold the brake pedal until the BRAKE light is off. Tada, the warning is gone and reset.

NOTE: This procedure worked on a 2001 E46 325i. It took about 15-20 seconds, but it cleared out w/o having to unhook the battery.

Other details find in the Owners Manual 2006-BMW-Z4m-Roadster-Owner-Manual

Keep us updated.

Nov 04, 2010 | 2006 BMW Z4 Roadster

1 Answer

Need to change out back brake light on 2006 nissan


take interior cover behind tail light inside trunk off.the bulb the bulb twist locks in hole(twist counter clockwise to remove)repeat procedure to replace.

Mar 23, 2010 | 2006 Nissan Altima

1 Answer

Nissan almera brake lights not working,checked fuse okay,changed bulbs still not working i don`t whats wrong.


Check the brake light switch under the dash at the brake peddle and make sure its working if it does not close when you depress the brake peddle the lights will not work You may hve to remove the lower cover for the dash to get at the switch

Aug 15, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...