Question about Cars & Trucks

Open Question

Bear whitetail 2 crossbow - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Main bearing cap bolt torque specs for a 1999 2.0 Ford engine


See #1; Main bearing diagram
See #2; NM conversion chart

  1. NOTE: The crankshaft must rotate freely; if necessary check and adjust the bearing clearances.Tighten the main bearings and connecting rod bearings.
    1. Tighten the main bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 90 degrees.






# 2) Newton Meters conversion chart:
http://extraconversion.com/energy/newton-meters/newton-meters-to-foot-pounds.html

#1)
25730427-ddvrxh52bv4dwu240r4mw22m-2-0.gif saailer

Jun 05, 2015 | Ford Cars & Trucks

1 Answer

Is there one or two rear wheel bearings on 95 Toyota Ford runner 4wd


If the axle flange has a series of nuts around the perimeter then you will have 2 bearings (tapered roller) per side. IF you have a flat flange and no nuts then you have a single ball bearing or taper roller bearing per side. I suspect 2 bearings a side as they run the same axle housing as a hi-lux

Sep 08, 2013 | Cars & Trucks

1 Answer

Torque settings for bmw 316 e36 big end bearings and main bearings


hi for main bearings it is stage 1 : 25nm leave for 10 mins then stage 2 its turn 53 degrees for big end bearings it is stage 1 : 23nm leave for 10 mins then stage 2 its turn 70 degrees hope this helps

Jan 01, 2011 | BMW 3 Series Cars & Trucks

1 Answer

2002 audi tt 225 bhp cranksharft torque settings


Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)


Nov 25, 2010 | Audi TT Cars & Trucks

1 Answer

Replace carrier bearing on driveshaft


the carrier bearing is a press off and press on bearing. drop the 2 mount bolts remove the 2 rear u bolts and take the front half to the auto parts store. takes about 2 minutes to presss on and off

Nov 06, 2010 | 1992 Chevrolet K1500

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

1 Answer

Torque specs


2002 2.0L Duratech.

Don't have 2004 2.3L

  • NOTE: Use new connecting rod bearing cap bolts.
    NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
    Install the bearing caps.
  • Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.
  • Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.
  • Coat the inner side of the bearing shells with engine oil.
  1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
    Tighten the main bearing and connecting rod bearing bolts.
    1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.
96fc939.gif

Apr 28, 2009 | 2004 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...