Question about 1997 GMC Jimmy

1 Answer

How to change iginition switch on 1997 gmc jimmy

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • GMC Expert
  • 495 Answers

Posted on Nov 29, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1997 GMC Jimmy turn signal switch

I have a 97 Sierra and similar issues. I changed the wiper control board that is under the hood/on the firewall/ mounted on the wiper motor.

Posted on Oct 06, 2008

  • 740 Answers

SOURCE: set timing 1997 jimmy

Ok that's pretty simple Put cylinder # 1 on TDC= top dead center on the (compressionstroke piston all the way up). Mark on metal part of distributor (with marker) where the number one is on the cap( that's where the number 1 wire plugs in) Then in-plant distributor make sure that rotor point is pointed to #1 on the cap, turn distributor shaft until this is achieved or as close as possible try to center shaft so you can adjust... ****** or advance to fine tune after you in-plant distributor if needed. Contact if you need more help . Good Luck

Posted on Jan 06, 2009

  • 6 Answers

SOURCE: 1997 GMC Sierra Truck Ignition Switch

its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure and always if u get confused i would highly recomend
a chiltons manual they explain things great

Posted on Feb 16, 2009

lindsay836
  • 677 Answers

SOURCE: How do you change a 2000 gmc jimmy blower motor?

How do you know the motor is bad ? Have you run 12 volts to it directly ?
We have the parts for you, and step by step instructions :
www.aescompaniesllc.com
Please click on contact us.

Posted on Feb 12, 2010

  • 75 Answers

SOURCE: replace water pump on 1997 gmc jimmy 4.3 litre

there are four nuts that you must remove at the front of the pulley between the fan. remove fan, fan shroud,loosen accessory belts. remove water pump pulley and the pump bolts will be exposed. check belts for replacement while you have them loose. reverse procedure to install.

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 GMC Jimmy ignition switch. Can anyone show me a picture of where this connector on the ignition switch goes?


Boy that sure looks like the steering column harness that hooks up to your multifunction switch, ends up to the left of the steering column underneath the dash.

Aug 27, 2016 | 1997 GMC Jimmy

1 Answer

Blinkers not working 97 gmc jimmy


You may need a voltmeter to check if power is going into the turn signal switch. Start at the turn signal fuse and see if power there, with key on.

Jan 12, 2014 | 1997 GMC Jimmy

1 Answer

Where is the relay switch located on 1997 gmc jimmy?


relay switch for what you have relay fuses under hood in relay box

Dec 11, 2010 | 1997 GMC Jimmy

1 Answer

Wont start--pulled starter bench tested ok


check your ignition did one of these before changed 3 starters before finding out it was ignition switch not making connection in switch good luck

Feb 07, 2010 | 1997 GMC Jimmy

1 Answer

How to change headlight switch on 1997 GMC Sonoma


easy job, remove instrument cover,switch is screwed on to that, unplug wires and remove switch,

Oct 03, 2009 | 1997 GMC Jimmy

1 Answer

My power window switch works on all the window except the driver side of my 1997 GMC Jimmy, what would the problem be?


Usually just a dirty switch. Take it out, take it apart and clean it with some electrical cleaner, or get a new switch.

Jun 07, 2009 | 1997 GMC Jimmy

1 Answer

1997 GMC Jimmy turn signal switch


I have a 97 Sierra and similar issues. I changed the wiper control board that is under the hood/on the firewall/ mounted on the wiper motor.

Oct 04, 2008 | 1997 GMC Jimmy

1 Answer

Blinkers light up don't blink. where is switch ?


in the steering column attached to your blinker arm.

May 28, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...