Question about Nissan Maxima

1 Answer

Clearfier wont side far enough - Maxima Nissan Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 500 Answers

Can you provide a brand/model #.. there are varactor diodes that can be changed to provide little more range. also a few changes could be made to the factory control.. depends on the circuit design.

Posted on May 07, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 77 chevy ignition wont let me start it


add a push start button its cheap and easy 2 wires one connected to positive post of battery 2 nd wire connected to starter place them on push start switch and thats that

Jun 25, 2013 | 1983 Chevrolet Silverado

1 Answer

How do i change out the heater core on 1995 1500 cheyenna truck?. do i need to remove the dash board?


No short cuts with this . however if you are good you can undo enough to get unit out from passenger side leaving the drivers side of dash up close to the sctreen and get pass side away far enough to get unit out. have fun

Dec 03, 2012 | Cars & Trucks

1 Answer

I have a 2002 sunfire... and i have trouble turning it on. Once it startes it is stuck there because it will not turn at all. Once it is in this position the wipes wont work, the windows wont roll down,...


sounds like you need a new ignition, reason nothing works cause once it doese turn over n starts the car the tumbler is stick in the starting position jus not far enough to keep the starter engaged but far enough the it still trying to go trough the start process which cuts the power to everything else till the ignition returns to the on postion

did you try jus turning the ignition far enough to when the starter engages jus let go of it so the car doesnt start and see if everything else still doesnt work if it dont i belive its the igniton

also with out starting it or engaging the starter as in just turning the key on to get power does anything work?

Jul 12, 2012 | 2002 Pontiac Sunfire

1 Answer

94 nissan pickup latch wont open hood?


The hood latch cable pulls a lever over towards driver's side of car to open the hood. Pulling the lever releases the hood latch.
This is the lever that is not moving over far enough to release, and the one you need to get to. You are right to think of removing the grill. Is it easy to remove? Often, someone can lay underneath and reach up with a prying tool (a screwdriver) and push that lever over. But if it's too far to reach, or if it's obstructed by parts or support pieces, just remove the grill to reach the latch.
Good luck.

Jan 24, 2012 | 1994 Nissan Pickup

1 Answer

I have a 2002 ford focus and changed the drive axle on the drivers side and it wont drive now


if you mean wont pull off in gear . it's probaly the axle is not in the tranny far enough - you hear or feel a locking sound when it goes in . sometimes you have to push or hit them where they will lock

Nov 05, 2010 | 2002 Ford SVT Focus

1 Answer

My door locks on the passenger side wont work, and my interior lights wont turn off, the windows also wont work. I have a 2002 jeep grand cherokee


you have a broken grond wire in the front pasanger door boot in the front door jam. very common on these and have to repair thwm all the time. you have to pull back the black boot and inspect all the wires and pull on the. sometime the break is up further and you can't see it because the boot don't pull back far enough. it most likely with be a black wire. good luck

Mar 14, 2010 | 2004 Jeep Grand Cherokee

1 Answer

1998 dodge 1500 wont shift


first of all standard or auto i am guessing its standed standard under drivers side hood near master cylinder there is a small clutch reservoir if there isnt enough fluid it wont extend the throw out bearing far enough for a shift because the clutch pedal is hitting the floor not enough fluid to extend the slave cylinder to drive the fork second faulty slave cylinder or throw out bearing as far as the light blown dash bulb or somone snipped the wire or took the bulb out

Sep 11, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...