Question about 1999 Honda Civic

2 Answers

Alignament rear suspension

Tires are getting geting bad from inside side

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Comprehensive suspension and alignment inspection will give the real reason for tire wear front or rear. Front wheel drive cars must be aligned at all four corners to insure proper tire wear and handling. Also proper air pressure should be maintained. Use tire makers recommendation ( on side wall ) as the car makers reccomendation is for best ride NOT best tire wear.

Posted on Jan 13, 2016

  • Larry Jackson Jan 13, 2016

    Comprehensive suspension and alignment inspection will give the real reason for tire wear front or rear. Front wheel drive cars must be aligned at all four corners to insure proper tire wear and handling. Also proper air pressure should be maintained. Use tire makers recommendation ( on side wall ) as the car makers reccomendation is for best ride NOT best tire wear.

  • Larry Jackson Jan 13, 2016

    Comprehensive suspension and alignment inspection will give the real reason for tire wear front or rear. Front wheel drive cars must be aligned at all four corners to insure proper tire wear and handling. Also proper air pressure should be maintained. Use tire makers recommendation ( on side wall ) as the car makers reccomendation is for best ride NOT best tire wear.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 70 Answers

I replaced the rear struts, when removing i discovered one was totally bad, they didn't seem bad from testing and recovered quickly when pushing on the bumper, but were bad. after replacing my rear tire wear is even after 5k miles. mine were wearing from inside to outside too.

Posted on Apr 22, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keep getting uneven wear on rear tire for 2004 lincoln ls


if the wear is on the inside of the tread ---wheel bearings , failed suspension bush,arm
if it is on the outside of the tire tread ,-- bent lower control arm
if it is patchy around the tire ---failed shocky
it is appears as if the tread is feathered towards one side of the tread--- wheel alignment
Tack it to an accredited suspension specialist shop for a proper examination and a rear wheel alignment

Jan 19, 2017 | Lincoln Cars & Trucks

1 Answer

Looking at what could cause the rear of the car to wiggle side to side when accelerating from 0 to 25 mph? the wheels do not look like they are wobbling when driving down the road! tire belts bad?


Tires...rear suspension...rear alignment - in that order. I had a car with a really bad rear alignment that hop sideways every time you went over a bump in the road.

Mar 14, 2015 | 2000 Oldsmobile Intrigue

2 Answers

Both rear tires are wore inside...Why,?...The tires are just new, a couple of months ago


Possibly have bad rear struts or other rear suspension wear or damage. Check the Toe In/Toe out are within specs.

Hope this helps, good luck

Les

Oct 31, 2013 | 1999 Pontiac Montana

1 Answer

Air suspension rear vehicle


INSIDE THE WHEEL OPENING TUCKED INTO THE FRAME WHERE THE REARWARD CRADLE IS LOCATED BESIDE THE SUSPENSION AIRBAG

Apr 26, 2013 | 2003 Lincoln Navigator

1 Answer

Rear tires wear on the inside


Time to check the rear suspension parts for wear and tear and get an alignment when done replacing the bad parts back there.

Jul 06, 2011 | 2002 Mitsubishi Galant

1 Answer

Coil above rear driver's side tire is practically


Blown suspension. You need to replace the spring and check the suspension spring supports. Also check all the others front and rear.

Nov 04, 2009 | 1994 Toyota Corolla

1 Answer

Flat spots on tire


This could be one of three things , either you have an alignment issue , bad suspension parts or just the lack of tire rotation. If the flat spots are at an angle from outside edge to inside edge then the problem is with your rear struts. If the flat spots are either on the out side edge or inside edge then the you have an alignment issue. If the flat spot are consistent all around the tire then you have a tire balance issue or bad rear struts.

Aug 31, 2009 | 2000 Buick LeSabre

2 Answers

Rear end has problems tires are bowes out bad


sounds like your problem is a bad bearing

May 01, 2009 | 2000 Ford Focus

1 Answer

How can the rear suspension be adjusted?


REAR WHEEL ALIGNMENT
TOE-IN : 0±2 mm (0±0.08 in.)
note_icon.gif 1. The rear suspension lower arm mounting cam bolt should be turned an equal amount on both sides during adjustment. Right wheel : Clockwise direction : toe-in Left wheel : Clockwise direction : ton-out Maximum difference between LH and RH : 3mm 2. The cam bolt should be adjusted within a 90° range left or right from the center position. CAMBER Standard value : 0°±30´ Maximum difference between LH and RH : 3mm : 0±2 mm (0±0.08 in.) note_icon.gif 1. The rear suspension upper arm mounting cam bolt should be turned an equal amount on both sides during adjustment. 2. Install the left and right springs which have the same identification color. 3. The cam bolt should be adjusted within a 90° range left and right from the center position.e55b100.gif TIRE WEAR 1. Measure the tread depth of the tires. Tread depth of tire [Limit] : 1.6 mm (0.06 in.) 2. If the remaining tread depth is less than the limit, replace the tire. note_icon.gif When the tread depth of the tire is reduced to 1.6 mm (0.06 in.) or less, the wear indicators will appear.

Jun 16, 2008 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
1999 Honda Civic Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...