Question about 2002 Dodge Neon

Open Question

These are the codes p0700,p0551,p0141,p0562,p0605,p0888. how do i fix most of theses? i have replaced the filter and the fluid in the transmission

Iam also about to replace the solenoid. should i replace the solenoid will it take care of most of theses codes, or would i still have a bunch more to do? the transmission hasnt been wanting to shift into 2nd gear, sometimes it will and other times it wont. please help

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: please help me i'm going crazy

po 551 is a bad power steering sensor are you sure it is the trans leaking and not the power steering po 700 is the output speed sensor on the trans either one of them is not hard to change you can do it!!!!!

Posted on Nov 22, 2008

  • 3 Answers

SOURCE: 2000 Dodge Sratus 4 speed auto transmission

Dave, The P0700 code is a generic fault code indicating the the TCM (transmission control module) has recognized a problem and the P0755 is the indicated problem. I'd recommend you check your transmission external electrical connector for water intrusion and corrosion at the terminals by disconnecting the connector. If nothing appears wrong, I'd then recommend you drop the lower transmission pan and take a look at the residue deposit that is laying on the bottom of the pan. You should only see a relativily minor amount of grayish, black clutch material residing there. Pay particular attention for a gross amount of this or any large particular material, including any metal, either filings or chunks, or any brass or aluminum. If this checks out to be fairly clean, then I'd recommend you replace that "B" solenoid (2-3 shift solenoid) and have the trans. pan and filter replaced.; I'd also highly recommend you have the trans flushed for anyother particular matter that may reside internally inside the transmission. You'll have to have the codes cleared and the transmission relearned for shift feel, at that point.

Posted on Jan 08, 2009

  • 291 Answers

SOURCE: wont shift all the time

remove the pan on bottom of transmission drain fluid...remove filter,, easy to locate by looking at the new one you bought....reinstall pan and fill with transmission fluid.....you can try this step...if still accurs.. need to have someone scan the transmission module.. alot of scanners only scan engine computer.. make sure to scan transmission module.. if no codes be very weiry about transmission failure that line of cars has a very bad reputation for bad tranny

Posted on Oct 10, 2009

  • 35 Answers

SOURCE: 91 dodge ram 1500 3-4 transmission shift solenoid

Transmission shop next.

Posted on Mar 07, 2010

  • 432 Answers

SOURCE: 2001 dodge stratus wont shift

Good Evening, I have a dumb question. have you cleared any current or history codes in the transmission? They will default with codes in the system. Also make note on what they are. If any and we can go from there, and yes tcm would be the next place to go but more info is best as far as codes and such.

Posted on Oct 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 chyrsler 300m it went in limp mode codes p0700. P0340 p0344 p0430 p0888 came up cleared the codes and now it knocks.


clearing codes wont correct the problem and limp mode is designed to protect motor and transmission - p0700 is a transmission problem
P0700 Transmission Control System Malfunction p0340 is camshaft position sensor malfunction
https://www.obd-codes.com/p0340 p0344 is also a camshaft position sensor circuit problem
P0344 Camshaft Position Sensor Circuit Intermittent your p430 is a cat converter problem
https://www.obd-codes.com/p0430 and p0888 is transmission relay problem these reasons are limp mode the knock can be fuel not burning correctly or a lower engine knock can mean you damaged a piston

Nov 08, 2016 | Cars & Trucks

1 Answer

Just changed filters and replaced fluid engine light came on with codes P0755 and P0888 what do I do?


According to RepairPal.com: " Common Problems That Trigger the P0755 Code
  • Defective Shift Solenoid
  • Defective Shift Solenoid wiring or connector
  • Defective Valve Body
  • Dirty transmission fluid that restricts the hydraulic passages"
According to Infinity Help.com: "P0888 - TCM Power Relay Sense Circuit"
AccA

May 04, 2015 | Cars & Trucks

1 Answer

I have a 2005 dodge grand carvan What do the codes p0700 and p0562 mean? and how do i fix it ?


P0700 is generic transmission code, transmission malfunction.. Have it read with a scanner to find the exact code. p0562 is battery voltage is low. Check positive and negative cables for corrosion and good connection. Also check the engine and body grounds. Make sure you have a engine to body strap/ground. They break. This could be the reason you're getting the p0700 code.

Oct 14, 2014 | 2005 Dodge Grand Caravan

2 Answers

What should i do to fix error code p0700 on a 2010 dodge caliber


p0700 is a transmission overall problem -tcm transmission control module problem u need to have the truck hook up to a diagnostic reader for the transmission -first check the fluid make sure full and not burnt[may need to change fluid and filter other than that their are to many problems that can cause the code

Mar 31, 2013 | Cars & Trucks

1 Answer

Error codes P0700, P0455, P0888 how to fix


the p0455 is an evap system code gross leak possible loose gas cap or broken vent line.the p0700 is a transmission code are you having any shifting problems if so you need to get a tester that can access the tcm(trans control module).i do not know what the p0888 is can't seem to find it.if your not haveing any driveablity problems check your gas cap and clear the codes.code info is available at obd-codes.com

Oct 06, 2012 | 2006 Chrysler 300

2 Answers

Can you tell me what the codes PO605 and PO700 are? PT Cruiser 2001


P0605-------- Internal control module read only memory (ROM) Error
Have the computor checked.
P0700-------- Transmission control system
Better take it to a transmission shop and have that checked so they can pinpoint the problem.

Aug 27, 2011 | 2001 Chrysler PT Cruiser

3 Answers

What does these codes mean P1781, P0731, P1784 AND P0700 AND HOW DO I FIX THEM.


p1781 is manufacturer control transmission, p0731 is gear 1 ratio incorrect, p1784 is manufacturer control transmission, p0700 is trans, control system malfunction. all of these codes refer to tranny.This code normally points to a faulty transmission control module, but this is an expensive part and you should have an experienced Dodge technician diagnose the problem first. or a transmission specialist. the other codes are probably associated with the p0700 code. have a good day !

Apr 27, 2011 | 2001 Dodge Grand Caravan

1 Answer

04 2.7 intrepid wont start .p0344 p0700 p0562


P0344 Camshaft Position Sensor Circuit Intermittent

P0700 Transmission Control System Malfunction

P0562 System Voltage Low

I would start with the P0562 issue. Check the battery voltage - it should be at a minimum of 12 volts (DC). You can try charging the battery with a trickle charger overnight and if the voltage does not come up to 12 volts then you should replace the battery. If it comes up to 12 volts then try starting it up if it starts you should get the alternator checked out at a garage. A simple alternator check is measuring the voltage at the battery you should get between 13.2 to 18.2 volts when the vehicle is running. The low voltage may be the cause of the other two codes. If not the P0344 indicates you may need to replace the sensor or if the timing slipped you may need to replace the timing chain / belt. The P0700 could indicate a low fluid condition or it may mean take it to a transmission mechanic.

Nov 28, 2010 | 2004 Dodge Intrepid

2 Answers

Transmission Problems


code P0700 means that there is a code in the trans controller. P0605 means there is an internal failure in the trans controller that can not be repaired. The only step in checking this code is replacing the trans controller. The controller is not the solenoid pack . Its the actual transmission computer.

Aug 10, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2002 Dodge Neon Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...