Question about 2000 Mercury Mountaineer

1 Answer

Faulty dpfe sensor - 2000 Mercury Mountaineer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 308 Answers

So what is your question

Posted on Apr 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code PO401


Exhaust gas recirculation module check:


1. Note the Differential Pressure Feedback Exhaust Gas Recirculation (DPFE) sensor voltage through the scan tool or backprobe the Brown/Light Green (BN/LG) wire of the Exhaust Gas Recirculation System Module (ESM). Voltage should indicate a reading of 0.5-1.2 volts.

2. If the voltage of the DPFE sensor is out of range, low or high, disconnect the ESM and note that the voltage of the DPFE sensor circuit should indicate a reading of 5.0 volts.

3. If the DPFE sensor voltage is out of range connected and the reading shows 5.0 volts with the ESM disconnected, reconnect the ESM and verify that the Brown/White (BN/WH) wire shows a 5.0 volt reading and that the Grey/Red (GY/RD) wire shows to be a good ground, indicating a voltage of less than 0.1 volts. If these circuits check to be ok, replace the ESM due to a faulty DPFE sensor.

4. If the DPFE sensor voltage in step 1 is found to be ok, verify that both vacuum hoses to the ESM have full engine vacuum to them when it's running.

5. With the engine idling, backprobe the Brown/Pink (BN/PK) wire and hold it to ground. This should activate the Exhaust Gas Recirculation Vacuum Regulator (EVR) solenoid of the ESM. The EGR valve should open, the engine should run rough, and the DPFE sensor voltage should climb.

6. Replace the ESM for a faulty EGR valve, EVR solenoid, or DPFE sensor if the DPFE sensor or engine does not respond to ground activation of the BN/PK wire

Nov 10, 2013 | 2004 Ford Explorer

2 Answers

P0401 exhaust gas recirculation flow insuficient detected


depending on the year make and model of the vehicle, the most likely cause of this code is the DPFE sensor which controls EGR operation.

Jul 14, 2011 | Ford Focus Cars & Trucks

1 Answer

My 2006 escape 3.0 idles rough but seems to run smooth down the road.engine light is on and shows code po402 excessive egr flow. engine starts fine when cold, but cranks for about 10 seconds unless you...


P0402 Exhaust Gas Recirculation Flow Excessive Detected A code P0402 most likely means one or more of the following has happened:
  • The DPFE (differential pressure) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (most likely carbon buildup)
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vacuum
  • Solutions
  • With a P0402, it is common for people to replace the EGR valve, only to have the problem return. The most likely solution is to replace the DPFE sensor.
    • Check the voltage at the DPFE sensor both at idle and when the EGR is open
    • Replace the DPFE sensor

May 04, 2011 | Ford Escape Cars & Trucks

1 Answer

How much to fix the P0401 egr problem in a 2001 mitsubishi mirage LS with over 100k miles on it?


A code P0401 most likely means one or more of the following has happened:
- The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
- There is a blockage in the EGR (tube), most likely carbon buildup
- The EGR valve is faulty
- The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions: In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
- Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
- Clean out the EGR valve and/or tubing to remove deposits
- Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
- Replace the DPFE sensor (with a good quality / OEM one)
- Replace the EGR valve


Keep us updated.

Apr 14, 2011 | 2001 Mitsubishi Mirage

1 Answer

1997 volvo 960, check engine light on with P0401. These motronic 4.4 do not have EGR, p0401 mean insufficient EGR flow. How do you fix this if there is no EGR?


A code P0401 most likely means one or more of the following has happened:
* The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
* There is a blockage in the EGR (tube), most likely carbon buildup
* The EGR valve is faulty
* The EGR valve may not be opening due to a lack of vaccuum

In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
* Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
* Clean out the EGR valve and/or tubing to remove deposits
* Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
* Replace the DPFE sensor (with a good quality / OEM one)
* Replace the EGR valve

Check it and send us your advance.

Mar 02, 2011 | 1997 Volvo 960

1 Answer

2002 Mercury cugar P0401 and P1401


DTC P0401 - Insufficient EGR Flow

EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor EGR (DPFE). These things work together to deliver the correct amount of recirculation based on engine temperature, load, etc. The P0401 code means that OBD detected an insufficient amount of EGR.

Causes: A code P0401 most likely means one or more of the following has happened:
* The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
* There is a blockage in the EGR (tube), most likely carbon buildup
* The EGR valve is faulty
* The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions: In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
* Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
* Clean out the EGR valve and/or tubing to remove deposits
* Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
* Replace the DPFE sensor (with a good quality / OEM one)
* Replace the EGR valve


DTC P1401 - Differential Pressure Feedback Electronic Sensor circuit High Voltage

I think that you need a new DPFE; first check it, you could also have something restricted. There are ports in the throttle body that can cause this as well. Check THIS LINK.

Hope helps.

Nov 04, 2010 | Mercury Cougar Cars & Trucks

2 Answers

Service engine code P0402 for Ford Mustang


P0402 OBD-II Trouble Code - Exhaust Gas Recirculation Flow (EGR) Excessive Detected

What does that mean?
EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor (DPF). These things work together to deliver the correct amount of recirculation based on engine temperature, load, etc. The P0402 code means that OBD detected an excessive amount of EGR.

Symptoms
You may notice drivability problems such as the engine may surge off idle. There may also be other symptoms.

Causes
A code P0402 most likely means one or more of the following has happened:
* The DPFE (differential pressure) sensor is faulty and needs to be replaced
* There is a blockage in the EGR (most likely carbon buildup)
* The EGR valve is faulty
* The EGR valve may not be opening due to a lack of vaccuum

Possible Solutions
With a P0402, it is common for people to replace the EGR valve, only to have the problem return. The most likely solution is to replace the DPFE sensor.
* Check the voltage at the DPFE sensor both at idle and when the EGR is open
* Replace the DPFE sensor

Hope helps (remember rated and comment this).

May 27, 2010 | 2001 Ford Mustang

1 Answer

How to fix code 401 on 2001 eclipse


A code P0401 most likely means one or more of the following has happened:

•The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
•There is a blockage in the EGR (tube), most likely carbon buildup
•The EGR valve is faulty
•The EGR valve may not be opening due to a lack of vacuum

In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.

•Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticeable difference in RPM's with the EGR open
•Clean out the EGR valve and/or tubing to remove deposits
•Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
•Replace the DPFE sensor (with a good quality / OEM one)
•Replace the EGR valve

Mar 31, 2010 | 2001 Mitsubishi Eclipse

1 Answer

How do you repair codes PO141 and PO136 2000 Ford E-350 with a 5.4 engine


Causes A code P0401 most likely means one or more of the following has happened:
  • The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced, this is the common cause
  • There is a blockage in the EGR (tube), most likely carbon buildup
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vaccuum
Possible Solutions In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
  • Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
  • Clean out the EGR valve and/or tubing to remove deposits
  • Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
  • Replace the DPFE sensor (with a good quality / OEM one)
  • Replace the EGR valve

Symptoms There may be no visible symptoms to the driver. Poor fuel mileage, possible misfire, depending on O2 sensor position when sticking.
Causes A code P0136 may mean that one or more of the following has happened:
  • Faulty O2 sensor leak in exhaust close to O2 sensor, faulty O2 sensor is the common cause.
  • Short to voltage on O2 signal circuit
  • Open in circuit resistance caused by corrosion in connector
Possible Solutions
  • Replace the second oxygen sensor on bank 1
  • Repair open or short in signal circuit
  • Clean corrosion from connector

Sep 16, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

2002 ford focus p0401


Here is a list of possible causes for a PO401, hope this helps.

  • DPFE sensor signal circuit is shorted to ground
  • DPFE sensor VREF circuit is open between sensor and PCM
  • DPFE sensor downstream hose off or plugged
  • DPFE sensor hoses both off, loose or damaged
  • DPFE sensor hoses connected wrong (reversed)
  • EGR orifice tube is damaged or restricted
  • PCM has failed

Feb 10, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2000 Mercury Mountaineer Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...