Question about 2002 Chevrolet Tracker

Open Question

Diagram of rear brakes on 2002 chevy tracker

Need a schematic of rear brake shoe assembly for 2002 tracker

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 630 Answers

SOURCE: Need a parts diagram or assembly diagram for rear

brake-drum-remove.jpg Step 1. Remove the the brake drum from the vehicle. brake-drum-brakes-removed.jpg Step 2. Once you have the drum removed, it is a good idea to clean the area of dust with compressed air or brake wash spray. brake-drum-brakes-spring-removal.jpg Step 3. Disconnect the Springs, removing the outer one first using the brake spring removal tool. brake-drum-spring-removal.jpg Step 4. Remove the two springs from the brake shoes. brake-drum-adjuster-cable.jpg Step 5. Lift up on the Auto-adjuster and disconnect the adjuster cable. brake-drum-adjuster-cable-remove.jpg Step 6. Remove the Auto Adjuster Cable From the upper retainer and remove. brake-drum-spring-retainer-remove.jpg Step 7. Remove the two Spring Loaded Brake Shoe Retainers. brake-drum-adjuster-arm-remove.jpg Step 8. Remove the Auto Adjuster Arm by sliding it forward and pulling outward. Remove the Spring and arm as one piece. brake-drum-shoes-remove.jpg Step 9. Pull the shoes outward and forward from around the drive axle assembly.
brake-drum-shoes-colapse.jpg Step 10. Allow the shoes to colapse together so you can now remove the lower spring and adjuster with ease. brake-drum-park-brake-lock-ring.jpg Step 11. You are now left with one shoe still attached to the Park Brake arm assembly by one lock ring.. brake-drum-park-brake-lock-ring-removal.jpg Step 12. Use a flat screwdriver and twist to open the ring. Then pry up on one end and this will allow it to release and be removed. brake-drum-clean.jpg Step 13. Use brake wash and clean the all surfaces. brake-drum-lubricate.jpg Step 14. It is important to lubricate the 6 points that the shoes slide on to prevent any noise. Non-drying silicon brake lubricant works well for this. brake-drum-park-brake-lock-ring-install.jpg Step 165 Insert park brake arm pin in New brake shoe and install lock ring. brake-drum-shoes-assemble.jpg Step 16. Install the brake adjuster and lower sping. Pull apart and slide the assembly over the drive axle. brake-drum-shoes-install.jpg Step 17. Install Spring Loaded Retainers to hold shoes in place so you can install the adjuster arm/spring and adjuster cable. brake-drum-spring-install.jpg Step 18. Install the Brake Shoe Springs.
brake-drum-adjuster-arm-install.jpg

Step 19. Install the the adjuster arm and spring and attach cable.
brake-drum-install.jpg

Step 20. Install brake Drum.
Go to FreeAutoMechanic.Com

Posted on Jul 21, 2010

Ad
  • 14036 Answers

SOURCE: I need schematic for rear brakes for 2002 chevy

haynes manual has photos to show you how to work on rear brakes.

Posted on Jul 03, 2009

  • 13 Answers

SOURCE: Need 2002 Chevy Tracker rear brake diagram on how

install star wheel toward the self adjuster arm

Posted on Jan 22, 2010

dttech
  • 4803 Answers

SOURCE: i need a diagram of a 94 chevy 4x4 rear brake

The best diagram you can get is on the other side of your vehicle. Take only one side apart at a time. You can then look at the other side to make sure it is assembled correctly. (It will just be a mirror image)

Posted on Jan 11, 2011

  • 878 Answers

SOURCE: on rear drum brakes on

look in ask .com or you tube diagram for rear brake assembly s10 chevy

Posted on Mar 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

1 Answer

Brake adjuster spring keeps slipping off!


Hi Joe,it could be your e-brake cable that is connected to the back brake shoe.

May 07, 2013 | 2002 Chevrolet Tracker

2 Answers

Rear back brakes on my 2000 tracker keep falling apart and it distroys all the hardware in the drum


When you assemble the brake, make sure that the springs 16 and 21 are firmly located in the brake shoes and that pins 29 and its mate have their springs on them and the little recessed and slotted caps (18) are in place and locked in the slots. (I do not see all these parts in the drawing but I am sure you will know what I mean)

2009-07-26_162339_85077786.gif

Apr 17, 2011 | 2000 Chevrolet Tracker

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

1 Answer

REAR BRAKE SHOE ASSEMBLY DIAGRAM


You can go to autozone.com and register for full free online repair manual that has the diagrams you need and everything else you could want.

Nov 18, 2009 | 2002 Jeep Grand Cherokee

2 Answers

I need a diagram for the rear drum brake for 2002 Ford Ranger


Copy and paste this into your search window: 2002 ford ranger rear brake diagram

You should see four pictures pop up, select the brake parts diagram or the brake picture.

Sep 03, 2009 | 1993 Ford F150 SuperCab

Not finding what you are looking for?
2002 Chevrolet Tracker Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...