Question about Ford Laser

Open Question

Clutch take up close to floor on kn laser - Laser Ford Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 630 Answers

SOURCE: 1985 Pickup: clutch catches too close to the floor....

needs to be raised on the lift and adjusted for proper adjustment.
usually if it is too high it is ready for replacement

Posted on May 06, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I pushed clutch n while system was open and now Iwe can't bleed clutch system,99 Camry v6 mv20


close of the bleeder nipple
you may have to operate the pedal by hand to pull it op of the floor a few times
open the nipple with the pedal on the floor . close off the nipple while the pedal is down . repeat the process until the air is bled out

May 06, 2017 | Cars & Trucks

2 Answers

Clutch would not engage


First you must bleed the clutch fluid by pumping clutch pedal and holding down to the floor while a helper opens and closes the bleeder On the slave cylinder
If still no operation after that you probably need a clutch assy

Apr 22, 2014 | 2002 Honda Civic

1 Answer

Clutch peddle is low to the floor


Sounds like you need to adjust the linkage or possibly change the cable. You might need to change the clutch and pressure plate but that doesn't seem likely. I would start with the linkage.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

1985 Pickup: clutch catches too close to the floor....


needs to be raised on the lift and adjusted for proper adjustment.
usually if it is too high it is ready for replacement

May 06, 2010 | 1985 Nissan Pickup

1 Answer

Need to know how to bleed clutch for 1995 ford ranger


Does the clutch have the outer clutch slave or is it inside the clutch plate area, to know look on the left or right side for a clutch slave cylinder if it does not have one it's internal and a pain. If it has an out side one fill the master reservoir then go under the truck and crack open the bleed valve on the cylinder have someone pres the clutch pedal all the way down and hold it to the floor, then close bleed valve then allow the clutch back up and have them push it to the floor open bleed valve and close when all air comes out do this till the arm moves it's full travel about 2 inches. And if its one with a master inside the transmission it has to be power bleed and normally you can’t do it without pulling the transmission.

Jul 23, 2009 | 1995 Ford Ranger Supercab

2 Answers

Clutch ONLY engages close to the floor - how do I fix it?


Try to adjust the clutch to compensate. if the adjustments have already been made and, the pedal is very close to the floor while engaging. this will confirm pressure plate failure.

replace the pressure plate in this case.

Jun 20, 2009 | 1993 Volvo 240

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...