Question about Ford Expedition

Open Question

What is evaporative system purge contro circuit

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: evaporative emission control system

9 times Out of ten !!!
Did You Get Gas and Leave the Vech Runnung while Filling Up ??
This will turn CK ENG light On !! and Cause EVAP Code ??

Is The Fuel Filler Neck Rusty ?? UNDER VECHILE) any vapor leak preventing vacum to build will set this code !!!

Posted on Jan 07, 2009

Ad
cadman000
  • 607 Answers

SOURCE: Service engine soon light comes on, checked with a meter and it is showing evaporative purge control valve circuit, what is it talking about

The EVAPORATIVE PURGE CONTROL VALVE is located under the hood usually behind or near the back of the headlights. It it on the top of the Evap Charcol Cannister ( shaped something like a Quaker Oats box ) . Basically does not allow fuel vapors to escape into the air. Te purge valve will recycle the vapors through a charcol filter and sent to be reused as fuel., Problem could be caused by excessive fuel in the cannister, or the solenoid, or wiring, etc back to the computer.. Requires a lot of diagnosing. Hope this helps.

Posted on Apr 13, 2009

clifford224
  • 1975 Answers

SOURCE: 99 lexus GS-400 P420, where is the O2 sensor? Need Pics not words

Below is a picture of the location of both O2 sensors for your vehicle. Also the last picture is your evap. system. In the "dotted lined" area I would check for rotten or lose hoses in that area as well the vapor pressure sensor could be faulty as well. Hope this helps.

4_5_2012_6_18_20_pm.jpg4_5_2012_6_18_37_pm.jpg4_5_2012_6_18_51_pm.jpg

Posted on Apr 05, 2012

emissionwiz
  • 76848 Answers

SOURCE: Evaporative Emission Control System Purge Control Valve Circuit Opeat's your problem?

Possible causes- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control

Read more: http://engine-codes.com/p0444.html#ixzz296gIeNzB

Posted on Oct 12, 2012

perkins48
  • 14384 Answers

SOURCE: Check Engine light in 2001 Toyota Echo, fault codes PO440, 441, 446

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80380329#hd1-1-28 Here is what is listed for problems,couldn't find codePO446,click on link to view.

Posted on Oct 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a truck that popped up a P0443 code up and I've been trying to see what it is so I can get it fixed thank yo


P0443 - Evaporative Emission Control System Purge Control Valve Circuit Malfunction

Possible causes: - Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection

When is the code detected? An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description: The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

P0443 Information for specific makes: P0443 ACURA
P0443 CHRYSLER
P0443 DODGE
P0443 FORD
P0443 HONDA
P0443 INFINITI
P0443 ISUZU
P0443 JEEP
P0443 KIA
P0443 LAND-ROVER
P0443 LEXUS
P0443 MAZDA
P0443 MERCEDES-BENZ
P0443 MITSUBISHI
P0443 NISSAN
P0443 TOYOTA
P0443 Evaporative Emission Control System Purge Control Valve Circuit...

Jun 03, 2015 | Cars & Trucks

1 Answer

Code p1443


without knowing your make or model:

  • p1443
    Evaporative Emission Control System Control Valve
  • audi
    EGR Valve Position Sensor Signal Too Low
  • bmw
    Leakage Diagnostic Pump Control Circuit Signal High
  • ford
    EVAP Control System Purge Control Solenoid or Purge Control Valve Fault
  • hyundi
    EVAP System Tank Cap Missing
  • infinity
    Evaporative Emission Control System Control Valve
  • lexus
    Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 2
  • mazda
    Evaporative Emission Control System Large leak detected
  • mitsubishi
    EVAP Purge Control Valve 2 Circuit Malfunction
  • nissan
    Evaporative Emission Control System Control Valve
  • suburu
    Evaporative Emission Control System Vent Control Function Problem
  • suzuki
    EVAP Purge Control Valve Malfunction- Stuck Open
  • toyota
    Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 2
  • volkswagon
    EGR Valve Position Sensor Signal Too Low
  • Dec 07, 2013 | Cars & Trucks

    1 Answer

    Toyota echo won't start code 440 441 446


    Error Code: P0440
    Fault Location:
    Evaporative Emission (EVAP) System - Malfunction
    Possible Cause:
    Malfunction Indicator Lamp (MIL) active.
    Soution:
    Check Evaporative Emission (EVAP) System Sealing.
    Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
    Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

    Error Code: P0441
    Fault Location:
    Evaporative Emission (EVAP) System - Incorrect Flow Detected
    Possible Solutions:
    Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
    Perform Output Test.
    Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
    Check Evaporative Emission (EVAP) Canister.
    Perform Basic Setting.
    Check Pipes between Tank Breathing and Throttle Body.

    Error Code: P0446
    Fault Location:
    Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
    Possible Cause:
    Wiring harness.
    Evaporative emission (EVAP) canister purge valve.
    Engine control module (ECM).

    Feb 25, 2013 | 2002 Toyota ECHO

    1 Answer

    Code po449 2009 cobalt


    The PCM has determined that a malfunction exists in the electrical circuit for the vent valve/solenoid in the evaporative emission control system.

    Definition:
    EVAP (Evaporative Emission System) purge/vent solenoid circuit condition

    Explanation:
    The solenoids and system wiring are monitored for opens or shorts

    Probable Causes
    1- Purge or vent solenoids defective
    2- Check connevtor and wiring
    3- Fuel saturated vapor canister
    4- Failed EVAP vent solenoid

    Feb 17, 2013 | 2009 Chevrolet Cobalt

    1 Answer

    Evaporative Emission Control System Purge Control Valve Circuit Opeat's your problem?


    Possible causes- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
    - Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
    - Faulty Evaporative Emission (EVAP) Purge Solenoid Control

    Read more: http://engine-codes.com/p0444.html#ixzz296gIeNzB

    Oct 12, 2012 | 2001 Mercedes-Benz ML 320

    1 Answer

    Repair 1997 ford taures purge control valve


    Well there is no one thing that causes this fault code but here are what can trigger the fault in the fuel vapor control system.
    P0443 FORD - EVAP Purge Control Circuit
    Possible causes- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
    - Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
    - Faulty Evaporative Emission (EVAP) Purge Solenoid Control

    Apr 17, 2012 | 1997 Ford Taurus

    2 Answers

    Code says evaporator purge solenoid


    Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

    P0440 Evaporative emission (EVAP) system - malfunction

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0441 Evaporative emission (EVAP) system - incorrect flow detected

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0442 Evaporative emission (EVAP) system - small leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

    Possible causes: Wiring, EVAP canister purge valve, ECM


    P0444 Evaporative emission (EVAP) canister purge valve -open circuit

    Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


    P0445 Evaporative emission (EVAP) canister purge valve -short circuit

    Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


    P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

    Possible causes: Wiring, EVAP pressure sensor, ECM


    P0455 Evaporative emission (EVAP) system - large leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0456 Evaporative emission system - very small leak detected

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


    P0457 Evaporative emission system - leak detected (fuel cap loose/off)

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


    P0458 Evaporative emission system, purge control valve -circuit low

    Possible causes: Wiring short to earth, EVAP valve


    P0459 Evaporative emission system, purge control valve -circuit high
    Possible causes: Wiring short to positive, EVAP valve


    Evaporative Emission Purge Solenoid

    Description & Operation
    The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
    During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
    The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
    Removal & Installation
    The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

    1. Disconnect electrical connector at solenoid.
    2. Disconnect vacuum lines at solenoid.
    3. Lift solenoid slot from mounting bracket for Removal & Installation.

    To Install:
    1. Position solenoid slot to mounting bracket.
    2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
    3. Connect electrical connector to solenoid.
    Purge solenoid location:

    jturcotte_65.gif
    EVAP cannister location:
    jturcotte_66.gif

    Nov 05, 2010 | 2000 Jeep Grand Cherokee

    2 Answers

    What does po440 on a 2003 saturn vue mean with a service engine soon light on


    That is a problem in the evaporative emission control system.
    Could be anything causing it
    Clogged filter in the charcoal canister
    A leak in one of the vacuum lines
    The purge valve not working,,,etc.
    The best thing is to take it and have it checked out, they might have to do a smoke test to find the problem.
    All they do is inject smoke into the system, if there is a leak the smoke will come out of it. All it takes is a pin hole in these emission systems to screw it all up.

    Aug 13, 2010 | 2003 Saturn VUE

    2 Answers

    I checked the codes and one comes up its po446. i dont under stand what it mean so i cant fix it to get the light to go out.


    P0446 Evaporative Emission System Vent Control Circuit.
    The following are descriptions of all Evaporative possible codes:

    P0441 Evaporative Emission System Incorrect Purge Flow
    P0442 Evaporative Emission System Leak Detected (small leak)
    P0443 Evaporative Emission System Purge Control Valve Circuit
    P0444 Evaporative Emission System Purge Control Valve Circuit Open
    P0445 Evaporative Emission System Purge Control Valve Circuit Shorted
    P0446 Evaporative Emission System Vent Control Circuit
    P0447 Evaporative Emission System Vent Control Circuit Open
    P0448 Evaporative Emission System Vent Control Circuit Shorted
    P0449 Evaporative Emission System Vent Valve/Solenoid Circuit
    P0450 Evaporative Emission System Pressure Sensor/Switch
    P0451 Evaporative Emission System Pressure Sensor/Switch Range/Performance
    P0452 Evaporative Emission System Pressure Sensor/Switch Low
    P0453 Evaporative Emission System Pressure Sensor/Switch High
    P0454 Evaporative Emission System Pressure Sensor/Switch Intermittent
    P0455 Evaporative Emission System Leak Detected (large leak)
    P0456 Evaporative Emission System Leak Detected (very small leak)
    P0457 Evaporative Emission System Leak Detected (fuel cap loose/off)
    P0458 Evaporative Emission System Purge Control Valve Circuit Low
    P0459 Evaporative Emission System Purge Control Valve Circuit High
    ---
    At least the cap isn't loose for the gas tank.

    I would clear the code with an OBD-II Scanner 'erase code' button, and see how long it takes for it to come back.

    Aug 06, 2010 | 1996 GMC Jimmy

    1 Answer

    I scann my car 2005 corollathe code came p0441and p0445 what does it mean engine light blinking


    p0441: Evaporative Emission Control System Incorrect Purge Flow;
    A code P0441 could mean one or more of the following has happened:

    Bad vacuum switch
    • Broken or damaged EVAP line or canister
    • Open in PCM purge command circuit
    • Open or short in Voltage feed circuit to Purge Solenoid
    • Faulty purge solenoid
    • Restriction in EVAP solenoid, line or canister
    • Corrosion or resistance in purge connector
    • Bad PCM

    p0445: Evaporative Emission Control System Purge Control Valve Circuit Shorted
    (This also came up already above)

    Nov 30, 2009 | 2005 Toyota Corolla

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    49 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...