Question about 2000 Oldsmobile Silhouette

1 Answer

AIr Bag System 2000 Odls. Silhouette

Air bag light on. Shows computer code B0058. RF Pretensioner Deployment Loop Open. This means replacing the pre-tensioner in the right front seatbelt. Anybody replaced one of these lately? Thanks Michael

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Make sure there are no bad connections under the right front seat. Usually it is just a bad connection. Try to clear codes and see if the code returns. You could also try switching the left and the right and see if the problems moves to the left side to be sure it is a defective pretensioner. If you do need to change it, just unhook the battery for 5 minutes. Then unplug and unbolt it. Hook up the new one and then hook the battery back up.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 ford f-350 passenger air bag flashes 1-7 code than stays on when truck is started.What does the code mean and can the code be reset without tearing air bag out of truck?


If a SRS fault exists, the RCM sends a message to instrument cluster module to flash a coded sequence which is called a lamp flash code (LFC) on the air bag warning indicator. Each LFC is flashed 3 times after which the air bag indictor will remain lit for the remainder of the key-on cycle. In addition to the self-test at start up, the RCM continuously monitors all of its external and internal circuitry for faults.
While the LFCs are an indication of a general concern in the supplemental restraint system (SRS), the DTCs are more specific. The DTCs can be retrieved from the RCM with a scan tool via the DLC.


DTC a c LFC b Description Action To Take - Continuous Lamp The Air Bag Warning Indicator is Illuminated Continuously (RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground) Go To Pinpoint Test A . B1048 c - Passenger Side Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test B . B1049 c - Passenger Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test C . B1054 c - Driver Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test D . B1057 c - Driver Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test E . B1231 13 RCM Crash Data Memory Full INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) and Inspection and Repair After a Supplemental Restraint System (SRS) Deployment in this section. B1317 Continuous Lamp Battery Voltage High REFER to Section 414-00 . B1318 Continuous Lamp Battery Voltage Low REFER to Section 414-00 . B1342 24 RCM is Faulted INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) in this section. B1871 25 Passenger Air Bag Deactivate Module Fault Go To Pinpoint Test F . B1884 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Circuit Failure Go To Pinpoint Test G . B1890 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Short to Battery Go To Pinpoint Test H . B2292 33 Restraint System - Seat Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test I . B2292 34 Restraint System - Seat Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test I . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault Go To Pinpoint Test K . B2434 53 Driver Seat Belt Buckle Switch Circuit Short to Ground Go To Pinpoint Test L . B2435 53 Driver Seat Belt Buckle Switch Resistance out of Range Go To Pinpoint Test M . B2477 54 Module Configuration Failure This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2607 57 Harness/Configuration Mismatch This DTC indicates the RCM is configured incorrectly. CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. B2691 53 Seat Belt Buckle Switch Circuit Fault, Front Driver's Side Go To Pinpoint Test N . C1414 29 Incorrect Module Design Level VERIFY RCM part number is correct for vehicle.
CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. U0100 14 Lost Communication With ECM/PCM REFER to Section 418-00 to diagnose the communication concern. U2023 14 Fault Received From External Node REFER to Section 418-00 to diagnose the communication concern. U2050 14 No Application Present This DTC indicates programmable module installation (PMI) has failed. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. a DTC: Diagnostic trouble code, retrieved using scan tool.
c Cross-link DTCs will be retrieved in pairs to identify the cross-linked components.
b LFC: Lamp fault code, flashed on air bag warning indicator.

Apr 18, 2017 | Ford Cars & Trucks

1 Answer

On my 05 ford five hunmdred the air bag light flashes 3 times then pauses and then flashes four times does this twice I think and stays on


Which light ? on the instrument cluster or the passenger side .
If a lamp fault code (LFC) is reported by the customer but is not present when the vehicle comes in for service, follow the Diagnostic Instructions procedure in this section to identify the intermittent DTC.

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence; a lamp fault code (LFC). The code is 2 digits. The first digit is flashed with a 0.5-second interval between pulses. There is a 2-second pause before the second digit is flashed which also has a 0.5-second interval between pulses. There is a 5-second pause between each display of an LFC.
Each LFC is flashed 3 times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority. Lamp flash code 34

B2292 d 34 Restraint System - Seat Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test R .
PINPOINT TEST R: LFC 33 AND 34/DTC B2292 - RESTRAINT SYSTEM - SEAT BELT PRETENSIONER FAULT NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the pinpoint test.
NOTE: The retractor pretensioner connector keying is different between vehicles. The retractor pretensioner connector shown in the following pinpoint test is equipped on the Five Hundred, the connector equipped on the Freestyle and Montego is similar.
Test Step Result / Action to Take R1 CHECK FOR CONTINUOUS OR ON-DEMAND DTCs
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards. WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow these instructions may result in the inadvertent deployment of the safety canopy and risk of personal injury. WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury. WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury. WARNING: Never probe the electrical connector on a safety canopy module. Doing so can result in safety canopy deployment. NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the SRS must be depowered. NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  • Enter the following diagnostic mode on the diagnostic tool: On-Demand Self Test.
  • Enter the following diagnostic mode on the diagnostic tool: Flag DTC B2292/ Record All Flagged Faults.
  • Enter the following diagnostic mode on the diagnostic tool: Retrieve/Flag /Record Continuous DTCs.
  • Was DTC B2292 retrieved during the on-demand self test?
Yes
This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to R2 .

No
This is an intermittent fault. The fault condition is not present at this time. Your best bet , take it to a qualified repair shop .



.

Feb 19, 2017 | 2005 Ford Five Hundred

1 Answer

2006 lincoln town car air bag light is on 5 beeps 5 times


The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action
  • Air bag warning indicator is illuminated continuously
  • Fuse
  • Damaged wiring, terminals or connectors
  • A faulty diagnostic connector
  • A faulted RCM
  • A faulty instrument cluster
  • Go To Pinpoint Test A .
  • Air bag indicator flashing
  • Air bag/pretensioner supplemental restraint system (SRS) fault
  • REFER to DTC Priority Table.
  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.
  • No communication with the restraints control module (RCM)
  • Fuse
  • Diagnostic tool
  • Data link connector (DLC)
  • A faulted RCM
  • Circuitry
  • Go To Pinpoint Test V .
LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

Jan 23, 2017 | Lincoln Cars & Trucks

1 Answer

Service Air Bag light on


DTC B0058 Right Front/Passenger Pretensioner Deployment Loop Open.
The passenger seat belt pretensioner deployment loop consists of a seat belt pretensioner-RF and the seat belt pretensioner-RF high and low circuits. A shorting bar used within the seat belt pretensioner connector shorts together both the seat belt pretensioner high and low circuits when the connector is disconnected. This will help to prevent unwanted deployment of the pretensioner during servicing. During a frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a diagnostic trouble code (DTC) will be stored in memory.
DTC B0084 Left Front/Driver Seat Position Sensor Circuit
The inflatable restraint seat position sensor (SPS) is used to determine the proximity of a front driver or passenger seat position with respect to the frontal air bag. The SPS interfaces with the sensing and diagnostic module (SDM). The state of the SPS allows the SDM to disable stage 2 of the frontal air bag for a front seat that is forward of a forward/rearward point in seat track travel. The SPS is a hall effect sensor that is mounted on the inside seat track of both the driver and passenger seats. The seat track includes a metal bracket that shunts the SPS magnetic circuit creating 2 states of seat position. The shunted state represents a rearward seat position. The non-shunted state represents a forward position. The SPS provides 2 current ranges, one range for the shunted state and a second range for a non-shunted state. These 2 states are inputs to the SDM. State 1 (shunted) being the rearward threshold and state 2 (non-shunted) being the forward threshold. When the SDM receives input from a SPS that state 1 threshold is reached (seat is rearward) the SDM will not disable stage 2 deployment, if required by the deployment sensors. When state 2 threshold is reached (seat is forward) the SDM will disable stage 2 deployment on the side the seat is forward. The SDM monitors the SPS circuit and if a fault is detected the SDM will set codes B0083 or B0084 and defaults to disabling stage 2 frontal deployment. This will only default on the side of the vehicle the sensor has a fault. Its important to understand that the SPS is secondary to the passenger presence system (PPS) and the manual instrument panel (I/P) module disable switch. If either one of these devices are in the disable mode the passenger air bag will not deploy regardless of the SPS status.
You should take this to a qualified repair Shop ! Takes special tools to test .

Feb 26, 2016 | 2006 GMC Envoy

1 Answer

What does the code b0026 mean on my 2009 buick lacrosse?


DTC B0026: Driver Frontal Deployment Loop (Stage 1) Open
It has to do with air bag system
B0026 Stage 1 or B0044 Stage 2 ?€¢
The steering wheel module stage 1 or stage 2 high circuit is less than 2.4 volts and the steering wheel module stage 1 or stage 2 deployment loop is more than 6 ohms for 500 milliseconds.


?€¢
The steering wheel module stage 1 or stage 2 deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.



has to do with

Jun 30, 2015 | 2009 Buick LaCrosse

1 Answer

What does air bag code 43 mean?


The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)


Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0043, (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)



Models:Tahoe

• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.

• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.

Apr 22, 2012 | 2003 Chevrolet Tahoe

1 Answer

Airbag light on. flashing 5 times 2 times then stays on


I think you have a false code stored due to your work. clear the code and you should be ok.
If the air bag indicator does not illuminate or the indicator stays on or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
Diagnostic trouble codes (DTCs) may not be displayed for approximately 30 seconds after the ignition switch is placed in the RUN position. This is the amount of time the air bag diagnostic monitor requires to perform all tests and verify system faults.
Each DTC (a series of flashes and pauses of the air bag indicator):
  • Represents a two-digit number.
  • Is always displayed at least twice.
If the diagnostic monitor detects a fault in the air bag system, a diagnostic trouble code (DTC) will be written to the diagnostic monitor's Non-Volatile RAM (NVRAM). This DTC will then cause the lamp to flash a lamp fault code (LFC) on the air bag warning lamp and can be retrieved with the New Generation STAR (NGS) tester. After servicing the DTC may then be cleared from the NVRAM.
If a system fault is present and the air bag indicator is malfunctioning, an audible tone will be heard. The tone is a series of five sets of five beeps. If the tone is heard, the air bag system needs attention.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor will attempt to remove deployment power by turning on a solid state switch to blow the 10A battery fuse.

If the 10A battery fuse has successfully been blown by the air bag diagnostic monitor, the air bag diagnostic monitor will not attempt to blow it again until the proper fault has been repaired and cleared (refer to Diagnostic Instructions). The air bag diagnostic monitor will store both the unwanted deployment diagnostic trouble code and the loss of deployment power diagnostic trouble code. The loss of deployment power diagnostic trouble code is the highest priority.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor has an internal fuse that that will blow (open) automatically. This removes all power to the air bag deployment circuit.
DTCs are prioritized numerically. If two or more faults occur at the same time, the fault having the highest priority will be displayed first. After that fault has been corrected, the next highest priority fault will be displayed.
The air bag diagnostic monitor includes an internal backup power supply. This feature provides sufficient backup power to deploy the air bag in the event the battery (10655) or battery cables are damaged in a collision before safing and air bag sensors close. The backup power supply will deplete its stored energy approximately one minute after the positive battery cable is disconnected.
---------------------------------------------------------------
Once a DTC is logged into the air bag diagnostic monitor memory, it will stay in memory until 80 key cycles have been recorded or until the NGS is used to erase the DTCs. Once 256 key cycles have been recorded since the concern was last detected, the DTC will automatically be removed from memory.
--------------------------------------------------------------
Active Command Modes
This command allows the technician to verify operation of the air bag system, indicator and tone. When the air bag output command is executed, the indicator and the tone are simultaneously activated for approximately four seconds. Both devices are automatically deactivated.


Air Bag Diagnostic Monitor DTC Priority Table DTC LFC Description Action To Take B1342 24 Air bag diagnostic monitor is faulted (retrieved only during On-Demand Self Test) GO to Pinpoint Test P . B1867 12/52 Lost or low battery voltage GO to Pinpoint Test A . B1869 — No air bag indicator — inoperative indicator circuit GO to Pinpoint Test R . B1913 13/53 Air bag circuit shorted to ground — driver/passenger GO to Pinpoint Test B . B1914 14/54 Air bag sensor circuit shorted to ground GO to Pinpoint Test C . B1921 21 Air bag diagnostic monitor ground circuit open or not mounted to the vehicle properly GO to Pinpoint Test D . B1922 22 Safing sensor output circuit shorted to battery voltage GO to Pinpoint Test E . B1924 24 System disarm fault GO to Pinpoint Test P . B1932 32 Driver side air bag module circuit high resistance or open GO to Pinpoint Test F . B1933 33 Passenger side air bag module circuit high resistance or open GO to Pinpoint Test G . B1934 34 Driver side air bag module circuit low resistance or shorted GO to Pinpoint Test H . B1935 35 Passenger side air bag module circuit low resistance or shorted GO to Pinpoint Test J . B1941 41 RH air bag sensor feed/return circuit open GO to Pinpoint Test K . B1942 42 LH air bag sensor feed/return circuit open GO to Pinpoint Test L . B1944 44 RH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test M . B1945 45 LH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test N .
DTC - Diagnostic Trouble Code, retrieved using New Generation STAR (NGS) Tester.
LFC - Lamp Fault Code, flashed on air bag indicator.

May 21, 2009 | 1997 Ford F150 Regular Cab

2 Answers

My 2003 ford expo has a constant airbag light lit after starting the veh. I have a new sensor, can't figure out were 2put it.. Please help.


first, you need to read the Lamp Fault Code, LFC from the flashing light. Here's how:

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence: a lamp fault code (LFC). The code is two digits. The first digit is flashed with a 0.5 second interval between pulses. There is a 2 second pause before the second digit is flashed, which also has a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority.
-------------------------------------------------------
The fault could be in the air bag circuits, the canopy circuits, the pretensioner circuit on the seat belts, etc.
Report back with code.

here's some of system.

SECTION 501-20B: Supplemental Restraint System 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants in addition to that provided by the three-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles can also be equipped with optional safety canopies that deploy from the A-pillar to the C-pillar upon a side impact or if a rollover condition is detected. If equipped with safety canopies, a unique restraints control module (RCM) is used.
See the following illustration for deployable component location.
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) Deployable Components a55c8c5.gif Item Part Number Description 1 611D10 Passenger air bag module 2 042D94 Passenger side safety canopy module 3 042D95 Driver side safety canopy module 4 61203 Driver safety belt buckle and pretensioner 5 043B13 Driver air bag module 6 14A664 Clockspring 7 61202 Passenger safety belt buckle and pretensioner

4ee7996.gif
Item Part Number Description 1 14B321 Restraints control module (RCM) 2 14B345 Second row, C-pillar side impact sensor 3 14B345 Second row, C-pillar side impact sensor 4 14B416 Driver seat track position sensor 5 14B345 Front row, driver door, side impact sensor 6 14B006 Front impact severity sensor 7 14B345 Front row, passenger door, side impact sensor

Apr 23, 2009 | 1997 Ford Expedition

2 Answers

Air bag light on


On my 2000 Oldsmobile Silhouette, the air bag light occasionally comes on. What I found is that under the drivers seat, there are some electrical connections. Make sure all of those are tight. Make sure you have nothing under the drivers seat pushing on the cables.

Mar 30, 2009 | 2000 Oldsmobile Silhouette

2 Answers

SRS light now repeatedly blinks 5-1 problem code - stop/reset?


Sounds like an air bag problem. You will not be able to reset the light without fixing the problem. The steering wheel airbag electrical contact is suspect. Airbag will have to be removed and problem repaired. . I do not recommend you repair the problem unless qualified.

Mar 12, 2009 | 1998 Lincoln Mark VIII

Not finding what you are looking for?
2000 Oldsmobile Silhouette Logo

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74115 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7188 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...