Question about Cars & Trucks

Open Question

Need firing order for 2007 santa-fe 3.3 - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: Santa fe

P0102 - Mass Air Flow (MAF) Sensor Circuit Low Frequency

P1702 TPS - Abnormal
P1702 TPS - Malfunction Adjustment
P1703 TPS - Low Input
P1703 TPS - Open/Short (Ground)

Posted on Sep 27, 2008

kakee
  • 1268 Answers

SOURCE: HOW TO YOU GET AT PRESSURE SENSOR ON COMMON RAIL HYUNDAI SANTA FE 2007 CDX

This is what it looks like

47cf2f5.jpg

Posted on Oct 28, 2008

  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

  • 1 Answer

SOURCE: 2007 Hyundai Santa Fe Limited

Hey all,
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com.  Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me.  The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar.  I added that alternate Step below in the instruction step.  Hopefully I'm able to insert the image of each instruction set so that the Figures are visible.  Its actually not that easy getting the rear rail covers off and its pretty easy to crack them.  I'd recommend gently rocking the covers for a couple minutes in order to loosen them up.  Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes.  If you have questions, go ahead and contact me.  I also took several photos of my install and that might be helpul.  Cheers!
-LePig
-----------------------------------------------------------------------
SANTA FE 2008 PIN U8210-28000 Cross Bar Assembly Installation Procedures
Kit Contents: • (2) Cross Bar Assemblies Required Tools: • Flat Head Screwdriver
INSTALLATION INSTRUCTIONS
1. Carefully unscrew and remove radio antenna. 2. Grasp the rear rail covers with both hands. Squeeze and pull up & inwards (toward the center of the vehicle) to remove covers. Take care not to break off the tabs by lifting the rear section of the cover first (Figure 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 2. - Alternate Method - Locate notch in rear of each cover to insert plastic pry bar.  Remove cover by prying up (with tool) and lifting rear at 45 degree angle (Fig 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 3. Check assembly clips for damage and dislocation. Replace if necessary. 4. Open the lever on one side of front/rear cross bar. Gently set the cross bar, with the arrows facing forward, into the channel of the side rails (Figure 2). Guide both sides into the track. 5. To adjust cross bars, open lever and place cross bars in desired location. Close lever (Figure 3). Try to move bars forward/back until they lock into place. 6. Reinstall rear covers by holding cover at a 45 degree angle and inserting the front tab into the rear of the roof rack. After aligning, snap cover in place (Figure 4). Be sure that the rubber lip does not interfere with the covers, and that the covers are fully seated. 7. Reinstall the radio antenna. Note: To remove the cross bars, remove the antenna, remove the covers, open lever of cross bar and slide to end of rail. Hold down locking fingers (on both RH/LH rear rail supports) with a flat head screwdriver (Figure 5). This will allow removal of cross bars from the rails.

81e769d.jpg

Posted on Feb 24, 2009

clifford224
  • 1975 Answers

SOURCE: Firing order 2005 v6 2.7

Here's a picture for you. Hope this helps and good luck.


clifford224_173.jpg

Posted on Mar 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2.7 L firing order


Coil pack front to back: 1-4-5-2-6-3 Firing Order: 1-2-3-4-5-6

Aug 15, 2015 | 2006 Hyundai Santa Fe

1 Answer

What is the firing order on a 2002 Hyundai santa fe


Common configuration is 1 - 3 - 4 - 2 for most cars of the four cylinder type -- I have not worked on a Hyundai Santa Fe so I don't know if this is a six cylinder or not and I cannot remember the firing order for six pot anyway .......... sorry

Aug 17, 2014 | 2002 Hyundai Santa Fe

2 Answers

2001 Santa Fe 2.7. What is the firing order


Check this diagram for 2001 Hyundai Santa Fe 2.7 liter DOHC V-6...


10_11_2011_12_57_57_pm.gif

Hope this helps (remember to rating this answer and leave us some testimonial comment).

Sep 24, 2011 | 2001 Hyundai Santa Fe

1 Answer

Need to know cylinder numbering on 2.7 litre v-6. where is number 1 located number 2 located etc. thanks


For the 2002 Santa Fe 2.7L V6:

Firing Order:
1-2-3-4-5-6

Cylinders:
....(back)
1.....3.....5
2.....4.....6
....(front)

Ignition Connections:
(back)
o <---3
o <---6
o <---2
o <---5
o <---4
o <---1
(front)

Mar 23, 2010 | 2002 Hyundai Santa Fe

1 Answer

The knob that secures the floor mat on drivers side is missing on my 2007 Hyundai Santa Fe. Can it be replaced?


Yes, definitely. Just go to your local hyundai dealer. if they do not have it in stock they will order in for you.

Mar 04, 2010 | 2007 Hyundai Santa Fe Limited

2 Answers

Need instructions to replace 2007 Santa Fe side view mirrors


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 18, 2009 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...