Question about Suzuki Tempter GR 650

Open Question

How to change input shaft seal on 1998 chevy s10

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jeffbvegas1
  • 520 Answers

SOURCE: Heater 1998 chevy s10

wide open hung thermostat can cause this too...continual circulation never allows the water to get hot enough to warm the heater core

Posted on Jun 23, 2009

Ad
  • 1509 Answers

SOURCE: 1998 Chevy S10 front axle will not engage when put into 4 wheel

Normal thing that happens as long as onone (worked) on it, is the vacume hose going to the engage sevevo under the battery box has fell of on either end or is brocken on the way there. Then the once or now leaky battery acid ate up this same servo. then the cable going to the front axel breaks sticks falls off or even someone needing one climbed under your truck while parked somewhere to get one to replace their brokeen one now you don't have one then theaxel engage arm or gearset is damaged

Posted on Aug 16, 2009

chitownbob45
  • 316 Answers

SOURCE: want to change a leaky seal on a axle shaft on

take off the housing cover in the middle of the rear end and to each side there is a retainer clip for each side. Pull it out and that side comes out. I don't think you needed to remove the rear end to do this though.

Posted on Oct 03, 2009

swoop611
  • 488 Answers

SOURCE: input shaft seal leaking after replace seal

Firstly, make sure the seal you fitted is the correct one, sounds silly but I have been given the wrong seals by parts people. It pays to check. Next, if you have fitted the seal correctly, and made sure that the seal is in flush with the housing, then it may be that the shaft is worn and may have a groove in it which was caused by the old seal. Pull the shaft out again and check for this groove in the shaft. If it does have the groove, you will need to find and purchase a steel sleeve which is fitted over the worn section of the shaft and ensures a nice clean and tight surface for the new seal to run on, thus stopping the leak.. Here in australia these sleeves are called "speedy Sleeves" and are available from any bearing shop and auto parts stores. The sleeve has a removable step on it which is used to tap the sleeve onto the shaft ( with a small hammer) and is then removed by twisting it sideways with pliers or sidecutters. The sleeve has a scored edge to help with this. Once you have removed the step, carefully clean up the edge with very fine grade rubbing paper ( wet and dry or fine emery cloth) with Oil applied to it to remove any sharp edges BEFORE you refit the shaft into the gearbox. This ensures that the new sleeve does not damage the seal. Re-assemble everything and test drive. As long as the seal is correct and fitted correctly and the sleeve is fitted correctly this will stop the leak. Have fun..

Posted on Oct 31, 2009

Testimonial: "thank you very helpful"

  • 1 Answer

SOURCE: drive shaft

I got to agree. ive had my 03 s10 since it came out and ive had to change the drive shaft 4 time.....the guy at the drive shaft place said that its a common problem wit the s10ii

Posted on Nov 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to know if a 1998 motor from a s10 will fit in a 1999 s10


once you have all the parts for the swap it should be a direct bolt in. its the v6 right?

Feb 14, 2014 | 1999 Chevrolet S-10 Pickup

1 Answer

I broke my driveshaft lastnight on my Chevy s10 I put a used on in today and now my motor is shaking bad what can be my problem please help


try greasing the shaft and bearings, also make sure the bearings are good and the shaft is in good order to stop the vibrations.

Nov 29, 2011 | 1998 Chevrolet S-10 Pickup

2 Answers

I have an 1998 chevy s10 automatic.this morning I noticed transmission fluid on the ground I checked and it comes out from a hose on top of the transmission but I don't see where it hook up?


From what I have read elsewhere: There is an overflow hose on top of transmission behind engine which actually is from the transfer case. Fluid will drip down onto exhaust and eventually catch on fire. Check transfer case for being overfull by taking the top fill plug out. If transmission fluid runs out, I believe the transfer case input shaft seal is shot and needs replaced. Mine caught on fire. I was lucky to get fire out before truck burnt to the ground. If you continue to drive vehicle at have something to put out a fire!!!!

Nov 13, 2011 | Cars & Trucks

1 Answer

How to change a torque converter seal on a 1984 chevy s10 4wd pickup


remove the transmission,remove the converter,and use a screw driver,and pry the seal out,then just tap the new seal in with a block of wood.

Apr 08, 2010 | 1984 Chevrolet Chevy

1 Answer

1986 chevy s10 trying to remove center bearing on


theres a collar on the youk.remove it and tap it out its splits the tow pieces of drive shaft.use alot of pb blaster and make sure you grease the youk theres a grease fitting there

Mar 27, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

Troubleshooting codes 1998 chevy truck S10 pick up were to find parts on truck ; codes p0171,p0401 ,p0452,p0131


p0171-System Adaptive Fuel Too Lean

p0401-EGR

p0452-EVAP Fuel Tank Pressure Sensor Low Input

p0131-Upstream Heated 02 Sensor Circuit

Hope That Helps.

Jan 15, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

Want to change a leaky seal on a axle shaft on


take off the housing cover in the middle of the rear end and to each side there is a retainer clip for each side. Pull it out and that side comes out. I don't think you needed to remove the rear end to do this though.

Oct 03, 2009 | 1998 Chevrolet Tracker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...