Question about 2006 Hyundai Getz 1.4

Open Question

Replace the inner driver door handle hyundai getz

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 25 Answers

SOURCE: Imobilising car alarm on Hyundai Getz

it may be worth while changing the battery in the remote as it takes more power to send the frequency to disarm than to illuminate the l.e.d.

Posted on Aug 23, 2008

Ad
ghost4548
  • 776 Answers

SOURCE: hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Posted on Jun 05, 2009

SOURCE: Fuse problem in hyundai getz

dear friend -the fuses you describe is cluster fuses and has nothing stopping or starting of the engine.they are joint in a yellow holder.i think you might have a short be hind the fuse box,thats wh you keek on blowing that fuse.

Posted on Jul 21, 2009

  • 12 Answers

SOURCE: Hyundai accent 1997, the driver side door handle broke

taking off the door panel is a lot of work. i can explain it all to you if you still have the same problem. i've replaced all of my door handles for all 4 of my hyundai's doors, so i'm experienced in this department. would you like a step by step walkthrough still?

Posted on Aug 05, 2009

  • 1 Answer

SOURCE: CHANGING A FUEL FILTER IN A HYUNDAI GETZ

I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TYRE SIZE HYUNDAI 1.3


Look on the label on the door or on the drivers side of the body just below the door latch

Jul 09, 2014 | 2005 Hyundai Getz 1.6

1 Answer

Looking to replace the inside driver's side door


i believe after you remove the door panel you can access the inner door handle and remove it from the door shell

Aug 21, 2013 | Cars & Trucks

1 Answer

Hyundai getz central locking system noy


It sound like you might have to replace the lock motor on the drivers door, it is possible the power or ground wires might be damaged and need repaired. But your problem most likely lies inside of your drivers door.

Apr 24, 2013 | Cars & Trucks

1 Answer

I have a "2009" 4-door Hyundai Accent and the


Being a 2009 you might have to buy a new 1 at the dealer.unless you get lucky and find 1 in a junk yard.Alot of inner door handles can be changed by removing screw for trim on handle(usually in the center of handle,might have cover over it if so pop cover off to revael screw) and remove door rods off back of handle.If not you will need to remove door panel.

Sep 03, 2012 | Cars & Trucks

1 Answer

1999 Hyundia accent door handles won't work


Go to ebay I bought two new outer handles and two inners for my '97 accent. They are five bucks a piece you can't beat it and free shipping. Take the inner panel apart if you're going to change them yourself. You have the mirror guard that pops right off with a flathead screwdriver, then unscrew every philips-head bolt on the panel there should be roughly four screws. Then once you remove the panel, two 10 mm bolts for the handle which are inside the door are what hold the handle on. Good Luck! http://www.ebay.com/sch/Car-Truck-Parts-/6030/i.html?_nkw=1997+Hyundai+Accent+door+handle

Aug 04, 2012 | 1999 Hyundai Accent

1 Answer

How to replace a door handle on a 2006 hyundai sonata, i either broke the handle and need to replace it or I am trying to figure out how to fix the drivers side handle


Step1: First, unscrew the 7 screws holding on the door panel
Step2: Next you carefully pry off the tweeter cover that is where the mirror is.Lift the panel up and off of the door . Undo all of the wiring connections except for the window controller.
Step3: Open the 2 black rubber view ports (Circled in Yellow) and roll the window up or down until you see the 10mm bolts that hold the window in place.
Step4: Loosen, but don’t remove these bolts. Slide the window up, and tape it up, or remove the window and set aside. Next, unplug the door lock plug and move the door panel out of the way.Unscrew the gold 10mm bolts that hold on the metal inner door panel . Also remove the Phillips screw that holds the inner door handle on
Step5: Unscrew the small bolt that holds on the lock cylinder that is behind the quarter-sized black cap on the side of the door. Be careful with that little bolt or it will fall into never land .Pull the lock cylinder out and set aside.
Step6: Now grasp the door handle, and with your free hand smack your hand holding the handle towards the back of the car. This will release the door handle.Under the door handle is a Phillips screw. Loosen this screw a few turns but don’t remove.
Step7: Now undo the 3 black star shaped screws on the door lock.You can now wiggle the inside of the door handle until it comes free. See the tabs that hold it onto the door . When you go to put it back on be sure the tabs get back in the right place.Pull the whole inner door panel and lock mechanism free by wiggling it out of where it sits.
Step8: Now you can undo the 3 cables; 1 from the outer door handle yellow mechanism, 1 from the inner door handle mechanism, and 1 from the inner door lock lever.Put on the new lock and put it all back together. Be sure to test it as you go. I had to turn the lock cable to the inner door lock lever 180 degrees because it was not unlocking properly when I put it back together the first time.
A couple of other notes, there are 2 pieces of plastic that are for the robots to use when putting the door together for the first time. one is a 3 pronged white plastic thing riveted to the inside of the metal door panel. The other is a white plastic thing covering the lock mechanism. You can cut off the fingers and throw the plastic cover away they are both useless and in the way.When you put it all back together, just go in the opposite order of disassembly. It is a little tricky to get the yellow plastic outer door handle holder into place. Be sure that the little tabs grab the metal of the door or things will not fit together properly.Be sure to test the power window after you put the window back in place. Do not overtighten the bolts on the window, it is glass…..

Apr 08, 2010 | 2006 Hyundai Sonata

1 Answer

How do I replace a '94 chev Astro outside drivers door handle


You first have to remove the inner door panel by taking the screws out of the inner handle and arm rest. the outer edges of the inner door panel either has screws or it has clips that can be pulled out. after you remove the panel you need to roll up the window and you will be looking at the back of the handle. simply un hook the clips that hold the lockrod and the inner opener rod and unbolt the outside door handle. reverse the prosses and walla.

Sep 19, 2009 | 1990 Chevrolet Suburban

2 Answers

Drivers door can only open from out side


sounds like inner door handle cable or clip has broke or came loose

Aug 06, 2009 | 2001 Hyundai Elantra

2 Answers

Removing 2004 hyundai accent door panels


STOP!!! there is no need to break the inner door handle!!! The inner door handle is secured in place with three prongs yes, but they do not need to be broken to remove it. They are secured by inserting them into place and sliding back. To remove simply slide forward and pull out.
This takes some wiggling but it will come eventually. also take note that this should be done after removing all screws and loosening and unhooking the door panel itself. To get the panel off around the inner handle, turn the panel 90deg and slide the handle back through its opening.
Good Luck

Dec 30, 2008 | Hyundai Motor 2004 Accent

1 Answer

Hyundai getz


if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Aug 28, 2008 | 2002 Hyundai Accent

Not finding what you are looking for?
2006 Hyundai Getz 1.4 Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...