Question about Cars & Trucks

Open Question

How do you replace a accelerator pedal sensor on a 07 suburban

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I need to replace Accelerator Pedal position Sensor

there is two little nuts on the bottom of the pedal itself just loosen the nuts and it comes right off.

Posted on Apr 29, 2009

Ad
clifford224
  • 1975 Answers

SOURCE: How to change 2004 acura tl accelerator pedal sensor

Below are some pictures and instructions for you. I'm just hoping that you have done all the diagnostics to be sure this is your problem. Have found in a few cases that there was a relay problem with the thottle actuator circuit. There is also a throttle actuator relay and sensor. Not sure what your problem is exactly but just hate to see parts replaced that are not needed. In any case the APP sensor is very easy to replace. Hope this helps you...

2_26_2012_10_37_18_am.jpg

2_26_2012_10_37_42_am.jpg
2_26_2012_10_38_06_am.jpg
2_26_2012_10_38_28_am.jpg

Posted on Feb 26, 2012

Testimonial: "Thanks Clifford that's really help me. To be honest, I'm not even sure what my problem is! Since the VSA and engine light pop up now the car is not raning smooth anymore so I thought it need to change APP sensor.."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

07 trailblazer. replaced the throttle body actuator and still wont come out of limp mode. Rough idle. ???


Code's stored ? APP - Accelerator Pedal Position Sensors Electronic throttle control ! Do yourself a favor an take it to a qualified repair shop .
017 Accelerator Pedal Position Sensors

May 13, 2017 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Need help with my suburban


1135 is the APP sensor, If this what you replaced and is still acting up. Look at the APP plug, Corrosion will also cause malfunctions. Clean it or replace it.

Jul 17, 2016 | 2003 Chevrolet Chevrolet Suburban 1500 LS

1 Answer

How can I replace the accelerator pedal assembly?


It's easy ! Disconnect the electrical connector , un bolt it .
Removal Procedure
Notice: Handle the electronic throttle control components carefully. Use cleanliness in order to prevent damage. Do not drop the electronic throttle control components. Do not roughly handle the electronic throttle control components. Do not immerse the electronic throttle control components in cleaning solvents of any type.
Remove the connector position assurance (CPA) retainer. Disconnect the accelerator pedal position (APP) sensor electrical connector. Reposition the carpet to access the lower nut.
Remove the accelerator pedal nuts. Remove the accelerator pedal assembly.

Feb 09, 2016 | 2003 Chevrolet Suburban

1 Answer

When I push on the gas pedal to accelerate my truck it does nothing then about 4 seconds later It jults forward and accelerates any ideas?


Sounds like it is the throttle position sensor . This tell your computer that you are pushing on the pedal to go faster or slower . You may want to go to UTUBE and put your year and brand of truck in , like this Example : 2001 Chevy Suburban Change out throttle position sensor with 5.7 liter ( This is my truck ) . Hope this helps , Grant

Aug 11, 2014 | Cars & Trucks

1 Answer

Suburban transmission shifting


Kickdown cable unhooked, attaches next to accelerator petal cable.

Apr 01, 2014 | 2003 Chevrolet Suburban 1500

1 Answer

2005 chevy suburban 5.3 engine hesitation


http://engine-codes.com/p1125_chevrolet.html
According to that website above, its your Accelerator Position Pedal Sensor. If you have already replaced it check your wiring harness.
Here is a website that for your wiring diagram for your 2005 Chevy Suburban.

Nov 26, 2013 | 2005 Chevrolet Suburban 1500

1 Answer

Mazda 323 bj not exccelerating


ENGINE HESITATES WHILE ACCELERATION

LOSS OF ACCELERATION


It can be fuel pressure issue or it's the problem with accelerator pedal or its clogged filters causing there.

There are many other possibilities. I suggest you to go through the list of help links mentioned below, these will help you to confirm where the actual fault lies: -------

Jerks and Hesitates During Acceleration?

http://technoanswers.blogspot.in/2012/07/2004-dodge-town-country-jerks-and.html

-----------

Loss of acceleration?

http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html

---------

Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

--------

How exactly the Vehicles Accelerator Cable works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html

-------------

How exactly Vehicles Accelerator Pump Diaphragm Works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html

--------

2000 Toyota Avalon: Engine Lean Codes and Knock Sound on Acceleration?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html

---------

2004 Toyota Avensis: Acceleration And Deceleration makes noise on Front End?

http://whatisbyme.blogspot.in/2012/05/2004-toyota-avensis-acceleration-and.html

---------

Wheel hop under hard acceleration?

http://technoanswers.blogspot.in/2012/04/wheel-hop-under-hard-acceleration.html

--------

2009 Chevy impala accelerator pedal sensor?

http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html

---------

Nissan Pathfinder stalls and bucks on Acceleration?

http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html

--------

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

-------------

These details will help.

Thanks.

Dec 31, 2012 | Mazda 323 Cars & Trucks

1 Answer

2005 Mazda 6 4cyl AT Idles high after driving a while.


I would check the pedal position sensor. Do it when it's hot.
Mazda Car 2005-06
  • Accelerator Pedal Position Sensor

    Description & Operation

    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.
    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.

Testing

  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1-8% load or 0.4 volts with the accelerator pedal releasedAPP1-60% load or 3.0 volts with the accelerator pedal depressedAPP2 -8% load or 0.4 volts with the accelerator pedal releasedAPP2 -60% load or 3.0 volts with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % and/or voltage does not change smoothly, replace the sensor.
  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1 %-31.0-32.4% with the accelerator pedal releasedAPP1 %-69.8-81.8% with the accelerator pedal depressedAPP2 %-20.2-21.4% with the accelerator pedal releasedAPP2 %-58.8-70.8% with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % does not change smoothly, replace the senso

0996b43f80203317-l15fcbeisfileg1jtnhunp3x-3-0.gif

Jul 23, 2017 | 2005 Mazda 6

2 Answers

My gas pedal sticks on initial acceleration and is


Replace the accelerator cable since it is worn and sticking. It will loosen up as you say altough someday it will jamb up while your driving it which will be a dissater in most cases

Jul 10, 2010 | 2001 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...