Question about 2002 Dodge Neon

1 Answer

What is the belt tensioner pulley bolt size for dodge neon 03

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 88 Answers

15mm

Posted on Mar 15, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 412 Answers

SOURCE: removal of tensioner pulley in a 2003 Dodge Neon

the tensioner is part of the engine mount bracket..not serviced seperately as far as i know

Posted on May 23, 2009

  • 412 Answers

SOURCE: Can't remove a 2001 Dodge Neon AC/steering pump belt tensioner

THERE IS NO BOLT HOLDING BELT TENSIONER TO FRONT ENGINE MOUNT..TENSIONER IS PART OF FRONT MOUNT BRACKET..AVAILABLE FROM DEALER..YOU MUST REPLACE WHOLE ASSEMBLY AS FAR AS I KNOW..CHECK WITH YOUR LOCAL AFTERMARKET STORES,THEY MAY HAVE A KIT..ALSO CHECK WITH YOUR LOCAL DODGE DEALER

Posted on Aug 04, 2009

SOURCE: How to replace tensioner pulley on 2000 Dodge Neon

Make sure you locate the Serpentine Belt Routing Sticker before you proceed. If not make an excellent drawing and take a GOOD Picture. Do NOT try to just remember how it goes back on Should be a 15mm wrench to loosen tensioner to remove belt. Locate mounting bolts to tensioner and remove, replace with NEW tensioner tighten bolts then use wrench arc torque about 15 degrees should snug it down, reroute belt then using 15mm pull tensioner to either side of belt to install belt in correct route. Remove all tools and body parts from engine bay. Do not start engine if anyone is in the vicinity of engine bay. Belt may fly off if you did not do it right and cause all kinds of shrapnell, if it doesn't fly off, visually inspect belt before starting and after, I would suggest being very careful before during and after starting to insure safety.

Posted on Jan 05, 2010

  • 1 Answer

SOURCE: how to replace belt tension pulley for dodge neon 2002

The power steering and A/C belt is tensioned by a tensioner pulley. Mine went bad and was "screaming" I thought it was the power steering pump and I replaced it only to find that it wasn't the problem. I couldn't find any bolts and deemed it too much of a problem for me to replace at home. The shop had to drop the engine and transaxle assembly from the engine bay in order to get enough room to replace the pulley. The problem with many FWD cars is having enough room to work so if you have to replace it, the engine has to move because you only have about two inches of room otherwise.

Posted on Mar 27, 2010

  • 1 Answer

SOURCE: How do I replace the

You have to remove the whole bracket that the tensioner assembly is attached to then you can get at the bolts that holed the tensioner and pulley together to service. Have fun.

Posted on Jan 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt routing diagram for 2004 dodge neon


over p/s pulley,down to a/c pulley ,up to crankshaft pulley ,under tensioner pulley

Dec 05, 2012 | 2004 Dodge Neon

1 Answer

2005 dodge neon the idler pulley went out. How do I change wthe idler pulley?


You will have to go to the tensioner pulley and put a wrench on that bolt and apply presure in the allowed direction and take the belt off...look first to see if there is a diagram of how the belt goes back on if there isn't write one down before you take the belt off...might be a good time to inspect the belt for cracks and replace as needed.

Mar 26, 2011 | 2005 Dodge Neon

1 Answer

How do I replace the tensioner pulley on a 2005 Dodge Neon?


You have to remove the whole bracket that the tensioner assembly is attached to then you can get at the bolts that holed the tensioner and pulley together to service. Have fun.

Jan 02, 2011 | 2005 Dodge Neon

1 Answer

How to replace tensioner pulley on 2000 Dodge Neon


Make sure you locate the Serpentine Belt Routing Sticker before you proceed. If not make an excellent drawing and take a GOOD Picture. Do NOT try to just remember how it goes back on Should be a 15mm wrench to loosen tensioner to remove belt. Locate mounting bolts to tensioner and remove, replace with NEW tensioner tighten bolts then use wrench arc torque about 15 degrees should snug it down, reroute belt then using 15mm pull tensioner to either side of belt to install belt in correct route. Remove all tools and body parts from engine bay. Do not start engine if anyone is in the vicinity of engine bay. Belt may fly off if you did not do it right and cause all kinds of shrapnell, if it doesn't fly off, visually inspect belt before starting and after, I would suggest being very careful before during and after starting to insure safety.

Jan 05, 2010 | 2000 Dodge Neon

1 Answer

How do i get the old tension pully off of my 00 plymouth neon


Hello.
There should be some bolts that hold the pulley on to the motor. Check behind the bracket, I believe they are the bolt size of 9/16. If you are trying to get the serpentine belt off, you can also just have someone hold the pulley away from the belt as you maneuver the belt off the pulleys.
Hope this helps! -Steve

Dec 06, 2009 | 2002 Dodge Neon

1 Answer

How to tighten altenator belt on a 95 dodge neon . I see no way of getting my hands in there to do it.


You cannot tighten the belt. It is the Tension arm/pulley's job to do so. If the belt is loose, then it either means the belt needs to be replaced, its the wrong belt, its routed wrong, or the tension pulley/arm is bad.

Nov 15, 2009 | 1995 Dodge Neon

1 Answer

1998 Dodge Avenger serpentine belt issue


What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
  5. Connect the negative battery cable.

2.0 DOHC

Power Steering Pump And A/C Belt
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut.
  5. Connect the negative battery cable.

Oct 29, 2009 | 2000 Dodge Avenger

1 Answer

Water pump


Is it a 99 or an 03? Either way fairly simple. You will need to remove the splash shield on the passenger side wheel well. Removing tire is optional. If it is a 99, the pump should be located near the radiator. Loosen the bolts that hold the pulley on the pump before removing the belt. This will save you time later. Remove the belt, then remove the pulley. Take all the bolts out of the waterpump. Install in reverse order. If it is an 03, it is near the firewall side of the motor. Remove shield, loosen pulley bolts. The pulley will not come off until you get the water pump out, but you need to remove the bolts for it any way. Take the bolts out of the waterpump. You will need a pry bar to get the pump/pulley out. You can pry on the tensioner against the fenderwell and wiggle it out. Install in reverse order.

Mar 05, 2009 | 1999 Dodge Grand Caravan

2 Answers

How to replace belt tension pulley for dodge neon 2002


The power steering and A/C belt is tensioned by a tensioner pulley. Mine went bad and was "screaming" I thought it was the power steering pump and I replaced it only to find that it wasn't the problem. I couldn't find any bolts and deemed it too much of a problem for me to replace at home. The shop had to drop the engine and transaxle assembly from the engine bay in order to get enough room to replace the pulley. The problem with many FWD cars is having enough room to work so if you have to replace it, the engine has to move because you only have about two inches of room otherwise.

Jun 21, 2008 | 2002 Dodge Neon

Not finding what you are looking for?
2002 Dodge Neon Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...