Question about 1992 Toyota Tercel

1 Answer

Shifted from 1st to 2nd gear heard a noise, car will not go, like in neutral

Car idles in gear with clutch out but will not move

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 46,677 Answers

Check drive shafts for failure If shafts are moving check axle shaft for broken. Check cv and u-joints are not failed. If auto have pressure test done on box If manual it may be in the clutch plate torn out.

Posted on Apr 21, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 84 Answers

SOURCE: HARD TO SHIFT FROM 1ST TO 2ND GEAR

Clutch wouldn't affect this, unless the throw-out bearing hadn't been replaced- I'm assuming you aren't having trouble between other gears, so you should check into the synchronizer for the gearbox.

Posted on Nov 27, 2009

SOURCE: ENGINE LACKS POWER (4AGE) 1600 CC, 4 CYL, TWIN CAM

I had the fuel pump recently replaced i just assumed the fuel filter was replaced also cause my fuel pump is in the gas tank. My air filter is clean and I have 4 fuel injectors, no carburetor. A friend of mine who has looked at my car for me says it sounds like there is some kind of air leak but can't figure out where it is coming from?

Posted on Oct 28, 2008

  • 1 Answer

SOURCE: shifter seems to have shifted

just ram the shifter in your booty,.....duh

Posted on Jan 29, 2009

shocktroop40
  • 155 Answers

SOURCE: loud clanking noise in gear if the clutch is not engaged

Almost sounds like a throwout bearing problem. Either way, bring the car back and make them fix it. It will be covered under the warranty so dont let them try to convince you otherwise.

Posted on May 28, 2009

yotaguy
  • 232 Answers

SOURCE: problem with clutch and 1st gear only when car is warm

The spring in the pressure plate is bad,and when it warms up is putting uneven pressure on the friction disc.The reason why it only occurs in 1st is that the input shaft is spinning from 2nd to 3rd and so on.In 1st from a stop it has stopped moving.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Saturn SL transmission won't engage


hangon. your leaving something out. myguess is you had the ebrake pulled so the car didn't roll when it was in gear. and now the car wont move at all or what? you left alot of important info out. if it is running and wont move at any point you broke something in the trany or a driveshaft. you should not be able to shift the trany into any gear if the engine is running. the clutch is turning and unless the clutch is disengaged you wont be able to shift. knowing that i am guessing you broke it good and need a new trany

Sep 17, 2017 | Saturn SL Cars & Trucks

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

Car moves with shifter in neutral position,feels like in 3rd or 4th gear.with shifter in 1st or 2nd gear car will not move. engine dies when clutch is engaged.


car is in two gears disengauge linkage and put back in Mistral if is a too loader you may have to pull the shift assembly and manually shift thhe gears your shift forks may be bent

Mar 11, 2013 | 1991 Honda Accord

1 Answer

Manual transmission will not shift into any gear, even when the clutch is completely depressed. It's a hard shift to begin with and now when i have to come to a stop and say move it out of 4th gear and try...


The problem sounds like the clutch. If you put it in 1st., then start it up, does it try to move with you foot on the clutch? Does the clutch pedal feel different than normal.

Jun 24, 2009 | 1998 Ford Escort

2 Answers

Grinding gears from 1st to 2nd, 3rd to 5 ok


Either your clutch is getting bad, or you're shifting down too soon, and up too late. Try double clutching. Push in your clutch and push it into neutral. Release the clutch, fan the gas pedal, push the clutch again and shift into 1st. All this does is sychronize the speed of the transmission with the speed of the engine. There were, in the 60's, a lot of cars with the old "three on the tree" that you had to do this every time, and you get pretty good at it after a while.

Jun 02, 2009 | 1995 Hyundai Sonata

1 Answer

Loud clanking noise in gear if the clutch is not engaged


Almost sounds like a throwout bearing problem. Either way, bring the car back and make them fix it. It will be covered under the warranty so dont let them try to convince you otherwise.

May 28, 2009 | 2009 Toyota Corolla

2 Answers

1991 Caprice No reverse. Moves in neutral. All forward gears OK.


What engine? Rear wheel drive ?Sounds like shift linkage or cable out of adjustment slightly. Have a look at where cable or rod attaches to transmission for adjustment. If not sure of what your looking for get back to me with info.

Mar 21, 2009 | 1993 Nissan Maxima

1 Answer

Mitsibishi colt 97 stuck in 1st gear


Your link broke off. What might have happened is the car got stuck in 1st, and when you shifted to second, the link broke. Not too clued up on your car, but you probably need to drop the gearbox. On some cars you can take out the shifter without having to drop the box and still see if the link is broken. Good luck

Mar 18, 2009 | 2006 Mitsubishi Colt

1 Answer

1991 prelude drivetrain problem


Wow, that's weird! If the speedometer is moving, but you aren't, then yes, something in the axle is not connected to the wheel. Were there any weird noises or symptoms before this happened? Either the cv joint is completely shot (u should have heard noise when turning a long time before this) or the spline could be stripped, but that is something I haven't heard of. If the clutch was shot, the engine would rev, but speedo is connected to transmission, so the speedo would not work if the clutch didn't. Let me know if anything was going on before this happened, I have a 91 Prelude (2nd since 1994, love it). countrycurt0

Sep 16, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
1992 Toyota Tercel Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...