Question about Kia Sedona

Open Question

Engine management light help!!

I brought this car a few months ago. When i turn the key i dont see an engine management light appear on the dashboard. This leads me to believe that either the bulb has gone or been removed. How can i check this? Ive also had a diagnostics check as it keeps cutting out but shows no faults.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: audi a4 engine management light

Go to AutoZone or Advance Auto Parts and have them scan the ECU (they do it for free, where a shop will charge you). They'll give you the codes, and you can post them here. Once you do that, I can help you narrow it down.

Posted on Aug 07, 2008

Ad
chain saw
  • 94 Answers

SOURCE: Electrical problem Audi A4

ELECTRONIC STABILITY PROGRAM ( ESP) LIGHT FLASHES TO INDICATE UNSTABLE DRIVING CONDITIONS....WHICH WILL ALSO COME ON IF YOUR ENGINE IS MISFIRES.. CHECK THE COILS AND SPARK PLUGS FIRST THEN GO FOR FUEL..INJECTORS...FUEL FILTER CHOKED..HOPE I WAS OF SOME HELP TO YOU..

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: renault traffic 03 1.9dci low power until turbo

my trafic did the same.no power pulling away until the turbo kicked in and it turned out to be the airflow meter.Hope this helps as it cured mine.Plus non of them rev past 3800 revs its normal.

Posted on May 26, 2009

  • 1149 Answers

SOURCE: Car engine occasionally cuts whilst running, had

Hi:
I am pretty sure that fault code P0698 is for your throttle position sensor, or accelerator position sensor. Often, as this fails, you can clear the code, and it will come back on during throttle movement.

Posted on Dec 01, 2009

Testimonial: "thanks for help will show your message to mechanic to see what he can do"

  • 13 Answers

SOURCE: volvo s80 dashboard fault

This is a known problem although Volvo will not admit it. The dash needs to come out (10 min job) and sent away for a simple repair. Total cost is about £150 but you will need to get the SRS warning that will be showing in the LED message display cancelled by a Volvo dealer after the dash has come back. Don't try a scrapyard dashboard the ECUs have IP addresses. I used a company in Kent to do the repair. Get onto Google there may be a repairer more local.

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not start, no clicking sound from starter. any Ideas to start troubleshooting?


It would appear that that your starter itself is bad. You don't have to remove it to have it tested but you will have to get it started to get it to a CARQUEST or somewhere like that.

Dec 20, 2015 | 1995 Mercury Grand Marquis

1 Answer

Help me please : I have a 2002 toyota corolla that stalled and now it won't start


When you had engine light on you should go to auto zone,they do for free to check what codes you have then fix.Could be fuse or fuel pump try to check this first and try get scan for codes...

Oct 26, 2015 | 2002 Toyota Corolla

1 Answer

I have a spanner symbol on my 407. what does this mean??


You need to carry out the periodical car service due (e.g. engine oil & filter, air filter, fuel filter, cabin air filter). The "service" spanner symbol "reset" button is placed on the lower right corner of the dashboard. See picture below:

tdisline_303.jpg
Then you should reset the "service" spanner symbol by pressing on the "reset" button on dashboard, when ignition key is in OFF position. Hold the button pressed and turn ignition key in ON position. Hold the button pressed and see on the dashboard successive numbers will appear: "10", "9", "8", ... , "1", "0". Then release the button and switch OFF the ignition key. The "service" spanner symbol followed by "20000 km" (or "30000 km" depending of the engine type), will appear for few seconds after turning ignition key in ON position, and will dissapear after engine starting. The car service due was reseted.

Please do rate my response. Thanks!

Feb 21, 2011 | 2005 Peugeot 405

1 Answer

Car wont start


It is the battery - you must not have the cables securely placed on the terminals. The same thing happened to me a few months ago.

May 02, 2010 | 2006 Honda Pilot

1 Answer

2000 Buick Regal LS 3.6 - Flashing Dashboard Lights/Wont start


Most likely it is the ignition switch (the key ignition switch) in the steering column ($100 at a dealer).

It may be a loose negative battery ground cable, too.
Check the negative battery cable where it conencts to the engine ground. It may be loose, corroded, damaged, or otherwise not making a good ground contact.

Add a grounding strap ($11 - AutoZone) from the engine to the chassis. That may help, but it's most likely the ignition switch.

Oct 07, 2009 | 2000 Buick Regal

2 Answers

Check Engine Light '07 Saturn ION3


well with a check engine light on you really should have it brought somewhere to read the codes stored in your computer it dont make sense to guess at what the code or problem is,since there are several,several codes.it may be a 02 sensor,a evap code,i think a few of the auto parts places have code readers and read for free.

Sep 07, 2009 | 2007 Saturn ION-2 Quad Coupe

2 Answers

Car will not start.


hi..
Many cars these days are equipped with an immobilizer. (you can find more information about the immobilizer in your owner's manual). The immobilizer allows the engine to run only if the correct key is used. If your car has an immobilizer, you probable see a "Security" or Key-shaped light coming on on the dashboard every time you turn the ignition ON. If this light is flashing when you turn the ignition ON, it could mean that there is some problem with an immobilizer or the system does not recognize the key. If the immobilizer doesn't recognize the key, the engine wold not start at all, or would start and then die in few seconds.
You can try a spare key, if it won't work, your dealer is the place to call. Sometimes, the key is just need to be reprogrammed. On some cars you can find the information how to reprogram the key in the owner's manual..

thank u
rate me

Jul 20, 2009 | 1997 Buick Skylark

1 Answer

Ignition and Engine management light


Try applying a none liquid graphite lubricant into the ignition key hole, work it into the key hole with the key, DO NOT use a liquid lubricant on ignition switches it can short out the ignition switch. engine management light? bring it to autozone or advance auto ask to use thier code reader plug it in and check to see if the car is throwing a code then go from there.

Jul 02, 2009 | 1998 Honda Accord

1 Answer

Turn the key but nothing happens all electrics


Not all replacement parts are good. I would guess that the new ignition switch is bad. Its also possible that the wiring harness is loose where its connected to the ignition switch. You could try jiggling the wires.

Jun 27, 2009 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...