Question about 1999 Jeep Cherokee

Open Question

Changing a 1999 jeep grand cherokee fuel filter

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: 1999 jeep cherokee do you have to remove the fuel pump to replace

The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL

  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Posted on Feb 08, 2009

Ad
  • 58 Answers

SOURCE: replace fuel filter on 1997 jeep grand cherokee

If you have the V8 engine, the filter is actually part of the fuel pump. WHICH IS IN THE TANK

Posted on Jun 28, 2009

techbuster
  • 5081 Answers

SOURCE: shift indicator light 1999 Jeep Grand Cherokee

There are two parts to it, a voltage resistor, and the EL panel itself.

You need to remove the console first. There are 2 screws under the front rubber pad, two under the cup holder, two in the bin. Remove those six first, take the storage bin out, then slide the rear cupholder out, remove the two screws under the cup holder, and one in front of it.

There are a total of 6 flat screws, and 3 self tapping screws you have removed.

Put the parking brake on, shift the tranny to N, and the transfer case to the middle position if equipped.

Remove the entire console. Slide the shifter beezel as far up vertically as you can. There are 4 clips you ned to remove to do it.
You will see a blue and black wire running into the back. Follow those wires to the resistor. You will see a transparent EL panel attatched to the resistor by two clips.

Usually, one or both of these clips has come loose, causing the light to work intermittantly. Clip them back on, and turn on the headlights to confirm that the light works correctly now.

Re-install everything in the opposite order.

Posted on Oct 11, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to change the fuel filter on a 2003 grand jeep

The Fuel Filter/Fuel Pressure Regulator is combinated component in your Jeep; this is remotely mounted to the vehicle body, above the rear axle and near the front of the fuel tank (Fig 25 & 26 of the Repair Manual).

Check the WJ Service Manual Section-14-Fuel-System-Ewj14 (page 15 and next).

Hope helps with this (remember rated this help) Good luck.

Posted on Jan 13, 2010

moparhart
  • 245 Answers

SOURCE: 1999 jeep grand cherokee. p0152, p0141, p0161

All 3 codes are point to the o2 sensor
the one you want to replace is on the exaust manifold looks like a spark plug with a wire sticking out of it un plug the sensor and it turns to the left to get off install the new one and plug the new sensor in
Thanks

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep grand cherokee dies while driving


did you change the fuel filter, very common problem that gets over looked too many times

Nov 25, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Where is the fuel filter and fuel pump located on a 1999 jeep cherokee grand laredo? having issues want to change fuel filter thanks


Either above or in a little (removeable) metal "cage" almost directly over the rear axle. Follow the fuel lines and you can't miss it! Cheers!

Aug 08, 2011 | 1999 Jeep Grand Cherokee

1 Answer

WHERE IS THE FUEL FILTER LOCATED IN A 1999 JEEP GRAND CHEROKEE LAREDO 6 CYC


THE 1997 TO 1999 FUEL FILTER INSIDE FUEL TANK WITH THE FUEL PUMP ASSEMBLY.

Oct 28, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Where is the fuel filter located, ona 99 jeep grand cherokee?


Hello,

There are 2 filters.
  1. One is on the end of the pickup tube inside of the gas tank.
  2. The second is in-line, above the front edge of the gas tank, inboard of the frame member. It is part of the fuel regulator/filter assembly.

Here's a diagram:
http://www.wjjeeps.com/misc/fuel_filter_wj.jpg

Take care.

Jul 24, 2010 | 1999 Jeep Grand Cherokee

2 Answers

Where is fuel filter in 2000 Jeep Grand Cherokee and how to get to it


For 2000 Jeep Grand Cherokee the Fuel Filter is located under vehicle, driver side, below bed area, front of fuel tank, mounted on chassis in fuel line.

cc3326a.jpg

Fig. Fuel filter/pressure regulator location-1999-01 models




d1426b6.gif


Fig. Fuel filter/pressure regulator-Grand Cherokee
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply, return and pressure lines Mounting bolts Fuel filter/pressure regulator
To install:
  1. Install or connect the following:
    Fuel filter/pressure regulator to the body. Torque the bolts to 30 inch lbs. (3 Nm). Fuel pressure, return and supply lines Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary.


Gooe luck (remember rated this post).

Jun 01, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where is the fuel filter on a 2000 grand cherokee


2000 Jeep Grand Cherokee 4WD 4.0L MFI 6cyl:
The Fuel Filter is located under vehicle, driver side, below bed area, front of fuel tank, mounted on chassis in fuel line.

17a3ee3.jpg

Fig. Fuel filter/pressure regulator location-1999-01 models.

For more details, can search in the Jeep WJ Repair Manual.

Hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Were is the fuel pump on a 99 jeep grand cherokee, and is it hard to replace?


You will not like my answer.

The fuel pump is inside the gas tank.

You will need to drain the tank and drop the tank to gain access to the fuel pump via the top of the gas tank.

Mark sure your new fuel pump has a new screen/sock filter.

Change filter filter at the same time!

Jul 15, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...