Question about 2005 Dodge Neon

1 Answer

What happens when the cam position sensor goes bad on 2004 dodge neon

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Change the coil that feeds power to the cam follower switch.

Posted on Sep 14, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

  • 1596 Answers

SOURCE: cant find cam sensor in 2004 dodge stratus r/t

2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Posted on Feb 12, 2009

  • 19 Answers

SOURCE: 2005 dodge noen cam sensor

I own a 2002 neon sxt and recently had to replace the cam sensor it should be in the same place.
look on the right side of the motor you should see it. it'll have a small wire harness that clips in the top and its fastend with 4 bolts. Oh and take the battery out before you do it it makes it a lot easier.

Hope this helps.

Posted on Feb 25, 2009

michigan man
  • 3533 Answers

SOURCE: How to change the camshaft position sensor on a 2004 dodge neon s

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

rvrfsh
  • 3 Answers

SOURCE: location of crankshaft position sensor

I have a 2005 neon and i found mu crank sensor on the radiator side of the block driver side of center directly below the starter. I hope this helps..

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2001 dodge neon cranked without the cam sensor connected. what's wrong with this picture?


Changing the Cam Position Sensor on Dodge Neon ...

? 10:33
https://www.youtube.com/watch?v=ciCPQ0kVAQY
Dec 21, 2012 - Uploaded by VeeTheAmazingGreek
... had to change out the cam position sensor on my 2001 Dodge Neon. ... 1997 Dodge Neon no start, crank sensor problems - Duration: 26:53.

Dodge Neon Questions - It will turn over but has no spark ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusAug 9, 2015 - I did have a neon while ago and image crank sensor was bad ... my 1999dodge neon has no spark it will turn over but not fire i have changed the crank sensorcoil ... I have a 2001 Dodge Neon 2.0 with 140,000 kms on it.

Dodge Neon Questions - 2001 Dodge Neon will turn over ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusJan 7, 2013 - I have a 2001 Dodge Neon 2.0 with 140000 kms o... ... went about a month before this recent problem, fixed that with no problem now this. ... firing. you said you replaced the cam sensor, did you do the crank sensor as well? ... My 1996Dodge Neon won't stay running whenever I take my foot off of the gas.

Starting Issues and Trouble Code Due to Defective Cam ...

repairpal.com > Problems > Dodge > Neon

Feb 05, 2016 | 2001 Dodge Neon

1 Answer

Neon Code P0344


I believe that the splice for the cam sensor is about 8 inches back in the harness. Power to the cam supplies several sensors. I have fixed a few that the splice was bad, There is very little room to work in to get to the splice, but it's not impossible to fix.

Jul 13, 2013 | 2004 Dodge Neon

1 Answer

What happens when the o2 sensor goes bad on 2004 dodge non upstream and downstream


Check Engine Light Will come On The Sensors Are Measuring Exhaust Gas Bad o2 Sensor Could Damage Catalytic Converters.

Apr 20, 2013 | 2004 Dodge Neon

1 Answer

How do you check cam shaft end play with bad cam sensor


I can't say for sure how to stop the cam from walking. That question goes a bit beyond my area of expertise. If I were you, I would call a Dodge dealer and ask a service advisor if that is a common repair for that car, and if so if there is a resolution. I wish you luck!

Dec 22, 2011 | 2004 Dodge Neon

1 Answer

I have a 2004 Neon that begins to buck and hesitate at high rpm's


try pushing in on plugs on PCM, below and inboard from the driver's side headlight. The cam sensor goes to the bottom plug.

Apr 24, 2010 | 2004 Dodge Neon

2 Answers

Cam position sensor location find the location on engine


Mounted on the backside of the cylinder head.

Feb 03, 2010 | 2004 Dodge Neon

1 Answer

Camshaft Position Sensor code is recurring.


if you noticed hows theres not much slack in the pigtail connector to the cam sensor the wires can break at the bend. replacing the pigtail should fix it

May 25, 2009 | 2004 Dodge Neon

1 Answer

Cam Shaft Sensor Problems


Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Dec 15, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2005 Dodge Neon Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...