Question about 2005 Ford Fiesta Zetec

1 Answer

Fiesta goes into gear but wont move

Clutch recently went on my car, i got this replaced but yet the car would not move. I was then told that due to the clutch being completly burnt out that it had affected my gearbox so i got a new gear box fitted but yet the car still has no drive. it goes into gear fine but when lifting the clutch it makes a terrible grinding noise. please help, iv spent so much money trying to get my car fixed and it just seems to be problem after problem

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 310 Answers

Is cluth also renewd whit the gearbox???

Posted on Jul 07, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 61 Answers

SOURCE: 1999 1.4 Ford Fiesta: When

Hi There.
sounds like your release bearing has either collapsed or seized, either way you will have to drop the gear box and check it out... should'nt be a problem on a 1999 fiesta. just be careful not to pop a drive shaft and lose the transmission fluic on the floor.
Good Luck

Posted on May 03, 2011

alicantecoli
  • 22095 Answers

SOURCE: Gearbox wont stay in reverse

strip and repair job is only soloution the selector is worn or the gear its self is cream crackered

Posted on Nov 22, 2008

  • 9 Answers

SOURCE: THINK DRIVESHAFT HAS GONE BUT WHICH SIDE

If drive shaft is gone replace it. Raise the car once more Look at the cv boots and shaft put car in nuetral car off key in ignition shift selector in neutral emergency brake on. position yourself by the wheel and observe the cv boot and joints rotate unisom or together on one side if not replace it check on both sides inner and outer. Then check opposite wheel

Posted on Feb 27, 2009

c17hydro
  • 2984 Answers

SOURCE: grinding gearbox

Got to AAMCO for a free inspection.....best part....IT'S FREE!!!!! They will tell you what is wrong and will NOT perform maintenance without your consent.

Posted on Mar 12, 2009

freetek
  • 5568 Answers

SOURCE: fiesta started making noises either gearbox or

Might also be a tired pressure plate, warn clutch plate or one contaminated by lubricant. Your car may also have a hydraulic clutch which could be low on fluid. If, after the initial shudder, the tranny responds normally, the guts of the unit may be fine.

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Goes into gear without using clutch and wont move??


the clutch cable is jammed holding the clutch off or the master cylinder has a blockage in the compensating port holding the clutch off
replace either of what you have

Jan 31, 2016 | Cars & Trucks

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

1 Answer

94 ford ranger manual transmission goes into first gear and reverse just fine let off the clutch and the truck wont move.


part of a clutch job is removing the gearlever make sure the lever is secured properly and selects the gear correctly.
Orherwise your symptoms sound like a collapsed pressure plate or broken release bearing either defective part or something done wrong during installation of clutch

Apr 13, 2017 | Cars & Trucks

1 Answer

88 pathfinder wont engage


check your rear brakes brakes could be locked due to frozen park brake cable or cables

Mar 07, 2012 | 1988 Nissan Pathfinder

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

1 Answer

Hello, I own a 97 miata and the clutch goes in gear but the car does not move.


Do you mean: The transmission goes into gear but the car does not move? Is somebody in the habit of coasting the car down hills with the clutch in so they don't have to shift? Coasting down a hill with the transmission in a low gear can cause the clutch disc to spin so fast that centrifugal force throws the lining off the disc. I blew up my clutch man! If this is the case you need a clutch job to learn an expensive lesson. Or starting out in second or third gear and slipping the clutch to get the car going. Just as bad just as expensive! Most have been told not to slip the clutch, Not all have been told not to coast in gear. If you like to coast put the transmission in neutral and let the clutch out. If this is not the case then the clutch is hanging up internally, put the car in gear and let is set over night. Can you push it with the clutch up? You shouldn't be able to. Now push the clutch down and let it up. If you can push the car now it is hanging up (sticking) internally. The clutch master/slave hydraulic system needs looked at.

Jun 06, 2009 | 1997 Mazda MX-5 Miata

3 Answers

Ford Fiesta 1.25 Zetec - Gears not engaging so no drive power


Sounds like your clutch cable is caught. Try new cable.

May 19, 2009 | 2000 Ford Escort

2 Answers

Stuck in 5th gear


try bleeding your clutch

Aug 19, 2008 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
2005 Ford Fiesta Zetec Logo

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...