Question about Nissan Cars & Trucks

Open Question

What does the codes p0100, p0120, p0110 for the nissan x trail mean

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Hi i have a 04 reg mazda premacy 2.0 turbo diesel

P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
****

Posted on Sep 28, 2010

Ad
  • 51 Answers

SOURCE: code P0120 on 1999 nissan pathfinder 3.3L

P0120- Throttle Pedal Position Sensor/Switch A Circuit Malfunction

Posted on Feb 01, 2010

blueextc3221
  • 15935 Answers

SOURCE: hi, my 1996 mercedes E200 has quite few electrical

P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 28, 2010

blueextc3221
  • 15935 Answers

SOURCE: hi, i have a 04 reg mazda premacy 2.0 turbo diesel

P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
####

Posted on Sep 28, 2010

leedavidian
  • 1420 Answers

SOURCE: I have the engine check

Welcome to FIxYa.com
Description of codes are:
P01600 - Serial cable malfunction-- check connection,
Po115-Coolant sensor-indicates a open or short-circuit in the engine coolant temperature sensor circuit.

The P0401 code is Insufficient Flow Exhaust Gas Recirculation System.

The code is set when the engien computer detects less than the requested amount of EGR flow when the engine is hot and is under load.

What usually sets the code is an inoperative EGR valve, or a carbon clogged port under the EGR valve.

On your engine, the EGR valve is vacuum operated, and there is a little computer-controlled EGR solenodi valve in the vacuum hose that detemines how much vacuum the EGR valve gets. If this solenoid is bad, or there is a vacuum leak in one of the hoses, the EGR valve won't open when it should setting the code.

Since the dealer already cleaned the EGR valve tube, I would suspect your problem is likely due to a bad EGR solenoid valve or a leaky vacuum hose to the EGR valve.


Here is the EGR solenoid valve part number and list price:

P/N 3946038750 $40.59



I would clear the codes first and run engine for two min and re-check codes.



Write to me of the findings and we will go from there.





Regards, Lee Davidian


A Four Thumbs up ^^^^ is appreciated for answering your question.

Thank you, Lee Davidian

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loss of power,have these codes p0403,p0100,p0110,p0181


Hi,these are the codes,
p0403....exurst gas recirculation circuit malfunction,
p0100....mass volume air flow circuit,
p0110....intake air temperature circuit,
p0181....fuel temperature sensore a circuit performance,

It could be just one of these thats throwing the others out,so you will have to test them all seperatly,all the best,hope this was some help.

Feb 12, 2016 | 2003 Hyundai Santa Fe

1 Answer

MY TOYOTA SIENNA 2002 MODEL IS NOT STARTING AND IT SHOWS P0100 P0110 P01011 TROUBLE CODES


Sounds like your MAF sensor could be dirty, or burned out or it could be a broken wire going to it.

Jan 18, 2016 | Toyota Cars & Trucks

1 Answer

Nissan x trail engine problem


check wiring/connector, remove and clean with MAF spray

Jul 22, 2014 | Nissan XTrail Cars & Trucks

1 Answer

Nissan maxima code P0325,P0100 and P0110


Well, sometimes you get lucky replacing parts, but usually its something other than the component in question.
The trouble codes are a guide as to what to test, not what to replace.
Code 325 is for the knock sensor which could be a phantom code.
Code 100 is for a bad signal from the MAF sensor which may or may not be caused by a bad sensor. It could be a vac leak too.
Code 110 is for a bad signal from the intake air temp sensor. The signal tells the computer what the temp of incoming air is to help the computer decide how rich the fuel mixture should be.
You need to get the testing procedures for each code and follow them. I would skip code 325 and start with code 110.
The fuel pump was probably a waste of money unless you checked fuel pressure before you replaced it and it was low. Same thing with the O2 sensors. Very rare if both sensors fail at the same time.

Feb 28, 2013 | 1996 Nissan Maxima

1 Answer

Code po120 mazda protege 1.5 L..code po110...code po115.....code po195



P0110 DTC - IAT Circuit Malfunction

P0115 DTC - Engine Coolant Temperature Circuit Malfunction

P0120 DTC - TPS A Circuit Malfunction

P0195 DTC - Engine Oil Temperature Sensor Malfunction

Hope this helps to identifiy.

Oct 04, 2011 | Cars & Trucks

2 Answers

HAVE CODE PO420 IN MY CAR NISSAN ALTIMA 2002 2.5


this is a common code on nissans and it is due to the O2S1 sensor reading that the cat is operating below threshold-can be
;
- Three way catalyst converter Bank 2
- Engine Control Module (ECM) Program
- Exhaust tube
- Intake air leaks
- Fuel injectors may be faulty
- Fuel injector leaks
- Spark plugs may be faulty
- Improper ignition timing
- Engine Control Module

most of the time it can be corrected by a nissan dealer, by reprogramming the stringent maps in the ECM, and the put out bulletins saying they would cover it if under 80,000-8 years, so that is not going to work-check the other possible issues then make calls to the dealer and see if you can get them to treat you like a future customer instead of a bother.

Apr 19, 2011 | 2002 Nissan Altima

1 Answer

Hi i have a 04 reg mazda premacy 2.0 turbo diesel wich does'nt start it is showing 5 fault codes p0110 iat sensor circuit p0180 fuel temp circuit p0216 injection timing control circuit p1189 pump speed...


P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
****

Jul 03, 2010 | 2004 Mazda MPV

1 Answer

Hi, i have a 04 reg mazda premacy 2.0 turbo diesel wich does'nt start, it is showing 5 fault codes p0110 iat sensor circuit, p0180 fuel temp circuit, p0216 injection timing control circuit, p1189 pump...


P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
####

Jun 07, 2010 | 2004 Mazda MPV

3 Answers

Troble code P0170


Trouble Code: P0170 (3.4L V6 VIN V Auto)
Fuel System Too Rich or Too Lean (Bank 1) Print this code dataprint_icon_codes.gif Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
DTC P0100, P0101, P0110, P0115, P0120, P0121, P0130, P0133, P0136, P0135, P0136, P0141, P0153, P0155, P0201-206, P0300, P0301-P0306, P0401, P0402 and P0441 not set, engine running in closed loop at a stable engine speed, and the PCM detected the lean or rich fuel trim correction value was more than or less than a calibrated limit in memory.

Possible Causes:
  • Air leaks present in the exhaust manifold or exhaust pipes
  • Air being drawn in from leaks in engine gaskets or other seals
  • Base engine "mechanical" fault affecting one or more cylinders
  • Fuel control sensor is out of calibration (i.e., ECT, IAT or MAF)
  • Fuel delivery system supplying too much or too little fuel at idle or cruise (e.g., faulty fuel pump or dirty, restricted fuel filter)
  • One or more fuel injectors is dirty, leaking or stuck open/closed
  • HO2S element is contaminated, damaged or it has failed

Oct 11, 2009 | 1995 Toyota Tacoma

1 Answer

Hi, my 1996 mercedes E200 has quite few electrical problems,. scanner pulled out following fault codes: p1584, p1580, p0100, p0130, p0370, p0110.. please help :)


P0100 OBD-II Trouble Code

Technical Description

Mass Air Flow (MAF) Circuit Malfunction

Basically this means that there's a problem with the Mass Air Flow (MAF) sensor or circuit.

You will likely not notice any serious driving problems, but there may be symptoms like a general decrease in power or sluggishness.
Causes

A code P0100 may mean one or more of the following:

* The MAF may be disconnected, or a wiring connection may be bad.
* The MAF sensor may be faulty.

Possible Solutions

Use an OBD II Reader (or go tou your local parts store and they will for free) and reset the code and see if it comes back.
Then start with the cheapest, easiest repair procedures:

* Check the Mass Air Flow Sensor wiring/harness is connected properly and that there are no broken / frayed wires.
* Unplug and reconnect the MAF wiring harness a few times to clear the contacts.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information).
* Replace the MAF sensor.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jun 04, 2009 | 1999 Mercedes-Benz E-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...