Question about Cars & Trucks

1 Answer

1996 ford contour cooling fan assembly - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 752 Answers

Hi Derek, I'm glad to help!
I'm not positive what your asking because it only says "Cooling Fan Assembly" But, if they are not working it's either the motor is bad or a relay that drives the motors is bad. Also on some FORD products I have found the wiring going to the motor melted away and has no insulation on them and they touch together and blow the fuse if applicable. Hope this helps and have an awesome day Derek.

Posted on Jul 17, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tducksoup1
  • 7 Answers

SOURCE: 96 ford contour, temp gauge not working

first and foremost check the fuse box. there is a fuse for guages. The temp sensor is somewhere on the manifold and it will have a hard wire with probably a spring around it for protections that runs from the engine to the instrument cluster. You can remove the temp sensor and use a heat gun or propain heat and see if you get any kind of response. I suspect if all your other gauges are working the fuse is good. Most temp sensors do not use power only for lighting of the gauge, It just sends a resistance change to the water temp bulb and it moves the gauge. Is it a seperate gauge or in your insturment cluster? could be simple as a crushed line or the sensor went bad. It is normally self contained. I suspect it is a gauge and not a dummy light? if you can not get the one working in the instrument cluster I suggest going to and autoparts store and replace it which is very easy to do. You can remove the old sensor from the block and reinstall the new on in its place and run the cable back through where the first one was and mount the gauge in another area, It is very important to know the water temp since most computers use this info for setting the correct fuel to air mixture in a closed loop system. That is a diffrent sensor but you need to know the temp yourself to keep from blowing a head gasket or worse which can cause you lots of money to repair, I prefer to mount my own gauge seperate from the cluster, best of luck

Posted on Jan 02, 2009

  • 156 Answers

SOURCE: 1996 FORD CONTOUR 4CYL ROUGH IDLE ROUGH ACCELERATION

no problem. If you are getting that low of voltage on a load then you might want to test the alternator as well to make sure it is running at capacity.

Posted on Feb 23, 2009

emissionwiz
  • 76846 Answers

SOURCE: how to change rans filter on 1996 ford contour

You must remove the transmission pan, the filter is inside the transmission.

Posted on Apr 15, 2009

morse008
  • 1111 Answers

SOURCE: Draining Battery on 1996 Ford Contour

you will need to do a test with a battery light disconnect the negative wire on the battery and connect one end of the test light to the battery and the other to the terminal with everything switched off if the test light is lit you have a draw if it is not lit then it is something else sometimes door switches and glove box switches wear out and need added lift to properly shut the open circuit down

Posted on Aug 26, 2009

bunnydawg
  • 5158 Answers

SOURCE: 1996 Ford Contour 2.5l V6 how to insert front strut into knuckle

either put a jack under the strut (if you can do so safely and raise the strut or use a good pry bar to pull down on the A arm. make 100% sure the car is well supported with jack stands etc.

robert

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 Ford Contour is overheating and sometimes smells like electrical burning


Yes and no. The thermostat can cause a overheating concern but not really a electrical burning smell. I would also make sure the cooling fans
are working also.

Feb 14, 2013 | 1996 Ford Contour

1 Answer

1996 Ford contour engine cooling fan comes on high about a minute after starting car and wont turn off or slow down.


Well it could be a problem with the fan relay, or it could be a safety feature of the computer.
if the computer finds a problem with the cooling fan or the engine temp sensor, it will turn on the fan to try to prevent overheating. Even if the engine is cold.
If the check engine light is not staying on, I would check the fan relay for power and ground.

Feb 13, 2013 | 1996 Ford Contour

1 Answer

I have a 1998 ford contour and the cooling fan will not engage


Check your relay for the fan.....Its usually on the drivers side under the hood right over the tire.....Go to or call autozone and ask them the exact location

Mar 13, 2012 | 1998 Ford Contour

1 Answer

Engine cooling fan won't come on while driving


The electric cooling fan is not needed while the car is driving down the road. Air is being forced through the radiator and provides enough air flow to cool the system properly. The only time the cooling fan is required is when the A/C is in use or the coolant system temperature has reached 225F.

Sep 06, 2011 | 1996 Ford Contour

1 Answer

I need to reassemble the front wheel bearing assembly on a 1996 Ford Contour


If yyou only have one apart the remove the other one "slowly" to see how to put that one together.

Jan 23, 2011 | 1996 Ford Contour

1 Answer

1996 Ford Contour GL 2.0 DOHC Cool fan not coming on.


Did you check the 60A fuse in the engine compartment fuse box?

Jan 19, 2010 | 1996 Ford Contour

1 Answer

Radiator cooling fan unit


it comes out the bottom with the radiator

Jun 25, 2009 | 1997 Ford Contour

1 Answer

My cooling fan will not turn on 2000 ford contour


you need to replace the cooling fan because the resistor is in the cooling fan and it is best to go to a salvage yard and have them look it up on a computer and it will tell what fan will work on your car

Jan 12, 2009 | 2000 Ford Contour

2 Answers

Overheating ?


check to see if electric fans turn on in front of radiator

Jul 13, 2008 | 1996 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...