Question about 2008 Ford Fusion

1 Answer

Rear bumper on Ford fusion

Should my 2008 Fusion rear bumper have push pins under the bottom to keep from flapping??

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Yes, in a lot of places they use the push clips now, and if it's flapping, more than likely some have either broken off, or missed at factory, unless some collision damage was not put back together properly, which I'm sure you'd be aware of.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Are there holes for them? Then yes, if not then no.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2009 fusion SEL has data compass error after being rear ended and a shop did repair.


WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION ...

www.fixya.com/cars/t16705785-compass_error_2009_ford_fusion
Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

www.fordfusionforum.com/topic/9390-compass/
Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

Nov 08, 2015 | 2009 Ford Fusion

1 Answer

Rear brake cailpers won't collapse on 2007 ford fusion


Open bleeder valve & push caliper piston, in as
you rotate piston to screw in parking brake

Do this by hand,only use a clamp on the front calipers

Apr 08, 2013 | 2008 Ford Fusion

1 Answer

Need factory stereo and speaker wiring diagram for '08 Ford Fusion


2008 Ford Fusion Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Green
Car Radio Ground Wire: Black/Blue
Car Stereo Antenna Trigger Wire: Purple/Black
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Purple
Right Front Speaker Negative Wire (-): White/Orange
Left Rear Speaker Positive Wire (+): Brown/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

Feb 16, 2012 | 2006 Ford Fusion

1 Answer

Fusion rolls in park


Only one thing can cause this, the pin that locks the transmission when shifted to park position is broken/sheared off, the bottom pan of the transmission must be removed and the broken park pin (referred to as the Park Pawl pin) replaced

Oct 13, 2011 | 2008 Ford Fusion

1 Answer

How do I install rear brake pads on a 2008 ford fusion once calipers are removed?


unplug the brake fluid line from the caliper than squeeze the cylinders open then insert your new brakes into the clips then add more fluid and bleed the lines connecting them back to the brake caliper

Mar 10, 2010 | 2008 Ford Fusion

1 Answer

Where is the jacking point for a ford fusion


BEHIND MARKS ON LOWER EDGE OF ROCKER
PANEL FRONT AND REAR.

Jan 27, 2010 | 2008 Ford Fusion

1 Answer

The rear lights on 2006 ford fusion are not working, we replaced the bulbs and when we check the fuses, they popped?


check the contacts on the rear hatch they are on bottom panel and the bottom of hatch these make contact for rear lights when hatch is closed you are looking for dirty wet contacts or pins stuck in on hatch contacts also the contacts block on bottom panel is sometimes o/heated thro arcing and eventually plastic plug that plugs to this block burns and creates a short circuit whick will blow fuses as you mention remove this block and examine it is more likely your problem ? hope this helps?

Dec 18, 2009 | 2006 Ford Fusion

1 Answer

Replacing brake pads on 2006 ford fusion


IF POSSIBLE GET A HAYNES MANUAL OR USE ONE WHEEL AS
A REFERENCE WHILE WORKING ON THE OTHER. BETTER GET
THE BOOK ESPECIALLY IF YOU HAVE REAR DISC CALIPERS.

Jul 19, 2009 | 2008 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...