Question about Mazda Cars & Trucks

Open Question

Changing the cv joints on a mazda bravo b2500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 365 Answers

SOURCE: How to change front disc brake pads on 2000 Mazda

jack up car, remove the road wheels, at the rear of the caliper you will have 2 or 3 bolts holding the caliper onto the stub axle, remove the bolts and remove the caliper, remove the outer pad, leave the inner pad in place and use a "G" clamp to compress the brake piston until it has bottomed, if this is not done the new pads will not fit back over the rotor as the piston is too far out and the new pads are thicker than the old ones.
place the new pads in the caliper and fit over the rotor, replace the 2 or 3 bolts that hold the caliper in place, replace the road wheel, tighten the nuts and lower the car to the ground, pump the brake pedal to see if you have brakes, if you do have brakes take it for a test drive away from any traffic if possible

Posted on Jun 13, 2010

Ad
  • 5 Answers

SOURCE: CV Joint Replacement '92 Mazda mx3

I suggest getting a service manual. If you've never done one before, a book will explain a vehicle specific order of operations. Chiltons or Haynes are good. consider it $20 insurance. Good Luck.

Posted on Aug 19, 2010

steve_e_uk
  • 1675 Answers

SOURCE: I have a 99 mazda

hi the torque settings for the hub nuts are 236-318 Nm these are the drive shaft nuts that fit on the end of the shaft on the wheel hub hope that's what you required please rate and vote thanks

Posted on Sep 20, 2010

RufAsGuts
  • 32 Answers

SOURCE: mazda bravo blowing white smoke

With regards to the above problem, I have just recently experienced the exact same thing with a 98 Mazda Bravo b2500 (this is a diesel).The symptoms were after driving over some corrugated dirt roads the vehicle would not rev over 2000 rpm and at that point would blow heaps of white smoke and misfire, but would idle beautifully and rev smoothly up to the 2000 rpm. Also noticed when vehicle was cold it would drive good for about 5-10 mins then symptoms would start again.

Fuel filters were changed, sediment trap cleaned,different fuel tried and checked all lines and system for air entry, problem still persisted. While checking injector pump lift pump pressure I noticed that the pressure would drop right off at the 2000 rpm, maybe a lift pump problem?? After consulting the workshop manual I found there is a small stainless steel thimble filter under the injector pump fuel line input union bolt, held in place with a small spring. Pulled this out to have a look and it was full of crud, cleaned it all up and put back together and have a guess what......goes like a brand new truck!!

Cheers

Posted on Jul 09, 2011

emissionwiz
  • 76630 Answers

SOURCE: Mazda bravo b2500 gearbox diagram

Clarification requested on duplicate post of this problem.

Posted on Jul 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change cv joints on a Mazda b2500


Remove the wheel .remove axle nut. remove wheel hub. place drain pan under housing to catch oil. axle will pull out of housing .remove rubber boots remove wire clip and joint will come apart. you can obtain reconditioned shafts for a little more than the price of the two joints saves a lot of work

Jul 04, 2014 | Cars & Trucks

1 Answer

Mazda. Bravo b2500 why wont my turbo spool


Hi Samantha, Please explain what you mean by 'spool'. Regards John

Jun 06, 2014 | Cars & Trucks

1 Answer

Gearbox diagram Mazda bravo b2500


Here is a diagram of the box.
7_3_2012_8_14_35_pm.jpg

Jul 03, 2012 | Cars & Trucks

1 Answer

Mazda bravo b2500 gearbox diagram


Clarification requested on duplicate post of this problem.

Jul 03, 2012 | Cars & Trucks

2 Answers

I had my cv joints changed out and now my knocking sound is worse


Is the knocking only on turns from the front and it is a fast continual knocking?
If the installation was correct.......sounds like the CV joints are possibly defective.
When changing CV joints.......always put in complete shaft assemblies that use NEW joints....not rebuilt joints.The price is almost the same.

Sep 06, 2009 | 1995 Mazda 626

2 Answers

Replacing Ball Joints on 2001 Mazda B2500 (upper and lower)


its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them

Jan 07, 2009 | 2001 Mazda B-Series

2 Answers

Mazda bravo blowing white smoke


blowing white smoke is almost always a symptom of an engine coolant leak at the cylinder head gasket. remove each spark plug and look for a dis-colored plug to find which cylinder is leaking.

May 26, 2008 | 2007 Mazda B Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...