Question about 2008 Isuzu I 290

Open Question

2008 isuzu i290 with manual transmission won't start

Tried popping the clutch, it cranks,but won't stay running

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Alcatrazx
  • 65 Answers

SOURCE: Low beam headlight is out on 2008 i290

Hi

Most probably you are seeing a lot of clutter in the bonnet to put your hand in and change it right? The best way sometimes is to unbolt the headlamp , move it out change the bulb and back in. But another way would typically be to remove the battery (and battery holder plastic box) or air box (whichever is in the way) and then you should be able to access the headlamp cover from behind. Anyways in both cases you should find a metal clip holding the bulb. Unclip the bulb whilst making sure that you dont touch the new bulb with you hands while putting it in. Press its metal clip in place again. and be sure to mount the plastic cover at the back properly so no water goes in the headlamp if its raining.

It was nice to help you :)

Best Regards

Posted on Jan 07, 2009

Ad
snownbird33
  • 120 Answers

SOURCE: 2002 isuzu rodeo won't start

Good day;
the clutch switch is located on the clutch pedal support, if you put your hand on the clutch pedal run your hand up and the switch will be at the top. now if you are going to replace this switch I would try to adjust the switch first the amount of time it takes and this would confirm that it's the switch. ensure clutch pedal is fully returned, disconnect the electrical connector from the switch. loosen lock nut and tighten clutch switch by hand until switch is firmly against clutch lever. back the switch out 1/2 turn, the switch plunger should extend .02-.06" (.5-1.5 mm).
hope this helps

Cheers

Posted on Jul 13, 2009

  • 3640 Answers

SOURCE: 2007 Isuzu i290 emergency brake

on the bottom, look at the teeth that lock the brake. they maybe rounded off or need a little help. without these teeth it will not lock brake on. they are on the bottom of emergency brake handle. have a good one !!

Posted on Dec 10, 2010

  • 1 Answer

SOURCE: 1996 Isuzu Rodeo. Where is the manual transmission

REMORE FRONT 4WD DRIVE AXIS

Posted on Jun 14, 2011

  • 1 Answer

SOURCE: 2001 Isuzu Rodeo won't start.Car died while

it happend to me too,when i checked my belt it was loose and the free pully came off.make sure ur belt is tight.

Posted on Nov 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will that explain the problem with the belt popping off as well? the AC unit had been disconnected for quite some time now


Worn out Crank Shaft Damper (Pulley)

The A/C Compressor won't be a problem,
unless the bearing seized for the clutch pulley

Oct 26, 2012 | 1983 Lincoln Mark VI

1 Answer

2000 jeep wrangler wont start


If it won't crank, check clutch safety switch and cables for the starter.
If it cranks but won't start, you'll need to find out if it is ignition or fuel to know where to look next.

Jun 26, 2012 | 1994 Jeep Wrangler

1 Answer

Won't start


So it's a no crank condition? Do dash lights, gauges, and everything else work when the car won't crank over? If so, buy a cheap $5.00 testlight, and when the car won't crank, pull the small black wire off the starter solenoid. While someone holds the key in start (cranking) position and clutch pedal depressed, see if the black wire has power as it should. (Ground the testlight and just touch the wire's end terminal. If powered, the testlight will light up.) If power there, then the starter solenoid is failing. Toyota starters are very good units, but the solenoid's internal contacts get old and pitted.
If no power at the black wire, then the start circuit from ignition switch to clutch safety switch (on the clutch pedal) to starter relay to starter solenoid will have to be diagnosed. To double-check: take a single battery jumper cable and put it on the positive battery post connection. Put the other end of the jumper cable on the solenoid terminal where black wire was removed. Key can be off. Make sure car is in neutral, brake set. If starter now operates, solenoid is O.K., and it is a problem in the start circuit, -ignition switch, neutral start switch, or in the wiring.
Now find a grounding place for testlight under the dash. When car won't crank, check for power coming out of ignition switch on the black wire with white stripe. This is the start wire for the starter solenoid. Key must be in crank position. Wire shoud be powered-ignition switch is working. If no power, switch is failing. You can do the same for the clutch start switch-it's a simple switch, that when clutch is depressed switch is closed and passes power on from ignition switch to the starter relay (thus allowing power to the starter solenoid). Black wire, red stripe-this is wire from clutch switch to starter relay. When key is in crank, clutch depressed, this wire should be hot.
With me so far? Still haven't found a problem, or any loose connections? Next and last is the starter relay. It is located under dash, close to gas pedal, but under the center console, just forward and left of gear shifter. It can be tested and the wiring diagnosed there, but relays are cheap, so just swap in another and see if that helps.
If you have tried everything, and still no help, you could try a new wire from the relay to the starter solenoid. This is that black wire we started with. Older toyotas sometimes have a problem with degraded wiring not passing enough current to operate the starter

May 04, 2012 | 1992 Toyota Tercel

1 Answer

It will crank but won't stay running


installed new fuel pump and filter in 97 cavalier 2.2 the car will run for a couple seconds and shut off if you spary it with starting fluid it will stay running

Apr 13, 2012 | 2003 Dodge Durango

1 Answer

2002 saturn sl won't start, turn over but won't start


Done cars have a kill switch if they are low on oil. Check your oil. If the oil is good, it may be the ignition switch.

Jan 01, 2018 | 2002 Saturn Sl

1 Answer

My dodge dakota truck will not start. It has power we tried to pop the clutch too.


do you mean the truck won`t start and run or do you mean it won`t turn over with the key.if it won`t turn over with the key the you may have a starter problem.if you mean won`t start then it could be the fuel pump not working.with someone cranking the motor you should hear the fuel pump running with the gas cap off and listening at the filler neck.or hear it running listening under the truck at the gas tank.if you don`t hear it then you can hit the tack sharply with your hand or a rubber hammer,it hear the pump start to run then the fuel pump needs replacing.if not check the fuses under the dash and under the hood.if they are good then it may be the pump relay in the relay box under the hood and it should be marked on the box or lid.

Apr 16, 2011 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...