Question about Cars & Trucks

Open Question

I can't find a 6DM14 (12V/14AH battery that uses bolt connections

I bought a generator that needs a starting battery. The number info they gave me for the battery is. 6DM14 (12V/14AH I can't find it anywhere. the search took me to a sight that had a battery with these ratings but it had F2 connectors. Where would I find the proper battery at a reasonable price? The information in the book said to use a 12 volt battery 9Ah. The battery can only be about 4.25" tall.

Posted by Anonymous on

  • Nelson Roberts
    Nelson Roberts Apr 25, 2014

    I am also looking for a 6DM14 12V/14AH but with the f2 connectors I would appreciate that wsite that you had for this.

  • John
    John Oct 18, 2014

    I have a Predator generartor that I bought at Harbor Freight that call for a 6DM14 battery; I found a YTX9-BS with the same dimensions and power requirements on Amazon. It's sold by ScooterParts Depot. cost $35.85 with shipping included. It has bolt connectors.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dustyboner
  • 331 Answers

SOURCE: how many bolts hold Mitsubishi

there are only 10 head bolts on that engine. the 3 bolts your talking about, aren't bolts they are plugs and shouldn't be removed.
a60ce70.jpg7ff722a.jpg0385b42.jpg if your pulling the head with the intake manifold attached, make sure you removed the bolts from the support bracket under the intake manifold.

Posted on Oct 12, 2008

Ad
  • 8 Answers

SOURCE: coach battery not charging using shore power.

u have a simple problem If uare not holding charge...... u have a leak some where man. did u install ne thing new? are thier different things applyed to the battery that could run it dead or not allow u to get the correct amount of ampigze.

Posted on Mar 12, 2009

  • 10 Answers

SOURCE: Need 12 volt battery for yellow corvette from toys r us.

if you have the old batt just cut off the old plug on the batt and cut off the new plug just hook + to + and - to - with wire connectors and your done

Posted on Jul 13, 2009

  • 2 Answers

SOURCE: how do I get 12 volts at the factory installed trailer connector

You are correct. There is a fuse in the underhood fuse/relay compartment that powers up the pin. It is one of the larger fuses and should be labeled as "AUX". Also check that the power wire is connected to the AUX bolt terminal. They shipped from the factory disconnected and the cable was zip-tied to something below the fuse box.

Posted on Aug 26, 2009

Testimonial: "I knew there had to be something needed done, I'll check in the morning under the fuse panel for a wire to terminate and see what happens. sounds log"

  • 8404 Answers

SOURCE: Looking for manual or information

Typically, the 110 Volt will go into a power center which should include a small amp battery recharger. Your 12 volt lights should run off a 'house' battery which should be isolated from the truck battery, yet, the truck alternator should charge the "house" battery on the road. The device that allows this is called a Isolator. You may find a manual switch instead. You definitely don't want the house and truck battery to both run yourf coach with no recharge capability. Some systems have a 'emergency start" switch which allows you to use the house battery to start the engine. All 12 volt house stuff should run off the house battery and the battery should be recharged by the truck or the small battery charger. Do you have an evap frig? Runs on propane or electricity? It needs 12 volts whether it is running on gas or 110 Volts. The 12 volts runs the control panel and the heat to make it work is supplied by the gas or by a electric calrod if 110 is available.

I am pretty familiar with these electrical systems ... I seriously doubt you will find any information on your 20+ year old motor home. Typically, the printed specs and equipment and the data is obsolete before the ink is dry because the manufacturers use what is available as they build. If you have additional questions simply click on the "add comment" or the "reply" link and I will take a look-see.

I hope this answers your current question. Thanks for your interest in FixYa.com

Posted on Sep 07, 2011

Testimonial: "Thank You! I now have confidence in using the lights extensively as I now know it has it's own charging system. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing alternator on 2001 sebring..cant locate belt tensioner


The tensioner will be one pulleys that can be rotated on its armature to remove tension to the belt.
Removal & Installation 2.4L Engine To Remove:
  1. Disconnect the negative battery cable from remote negative terminal on shock tower.
  2. Remove the drive belt cover.
  3. Disconnect the wiring from the generator.
  4. Raise and safely support the vehicle.
  5. Remove the accessory drive belt splash shield and then remove the belt.
  6. Lower the vehicle.
  7. Remove the MAP sensor from the intake manifold.
  8. Remove the generator mounting bolts and the generator from the engine.
To Install:
  1. Install the generator and tighten the bolts to 20 ft-lbs (28 Nm).
  2. Install MAP sensor.
  3. Raise and safely support the vehicle.
  4. Install the accessory drive belt and splash shield.
  5. Lower the vehicle.
  6. Connect the wiring to the generator.
  7. Install the belt cover.
  8. Connect the negative battery cable.
2.7L Engine To Remove:
  1. Disconnect the negative battery cable from the remote terminal.
  2. Raise and safely support the vehicle.
  3. Remove the accessory drive belt splash shield.
  4. Loosen the accessory drive belt.
  5. Remove the generator lower mounting bolt.
  6. Lower the vehicle.
  7. Disconnect the wiring from the generator.
  8. Disconnect the electrical connector from the A/C pressure switch and clutch coil.
  9. Remove the engine oil dipstick.
  10. Remove the generator upper mounting bolts.
  11. Remove the generator.
To Install:
  1. Install the generator on the engine. Loosely install the upper bolts.
  2. Install the engine dipstick tube.
  3. Connect the A/C pressure switch and clutch coil electrical connectors.
  4. Connect the wiring to the generator.
  5. Raise and safely support the vehicle.
  6. Install the lower generator mounting bolt and tighten to 20 ft-lbs (28 Nm).
  7. Install the accessory drive belt and splash shield.
  8. Lower the vehicle.
  9. Tighten the upper mounting bolts to 20 ft-lbs (28 Nm).
  10. Connect the negative battery cable.
prev.gif next.gif

Feb 03, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

How to change the alternator on my 2000 grand voagear


This is for a 3.3L motor
Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

REMOVAL

  1. Release hood latch and open hood.
Removal/Installation of Battery Cables 81929864

  1. Disconnect battery negative cable.
  2. Remove windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  3. Remove accessory drive belt.
Generator Mounting Bracket 81929870

  1. Remove bolt holding top of generator mount bracket to engine air intake plenum.
  2. Remove bolts holding outside of generator mount bracket to generator mount plate.
  3. Remove bolt holding top of generator to mount bracket.
  4. Remove generator mount bracket from vehicle.
  5. Rotate generator toward rear dash panel.
Generator 81929868

  1. Disconnect the push-in field wire connector . from back of generator.
  2. Remove nut holding B+ wire terminal to back of generator.
  3. Separate B+ terminal from generator.
Generator Pivot Bolt 81929871

  1. Remove bolt holding bottom of generator to lower pivot bracket.
Generator 81929872

  1. Remove generator from vehicle
INSTALLATION

  1. Place generator in position on vehicle.
  2. Install bolt to hold bottom of generator to lower pivot bracket.
  3. Place B+ terminal in position on generator.
  4. Install nut to hold B+ wire terminal to back of generator.
  5. Connect the push-in field wire connector into back of generator.
  6. Rotate generator forward away from dash panel.
  7. Place generator mount bracket in position on vehicle.
  8. Install bolt to hold top of generator to mount bracket.
  9. Install bolts to hold outside of generator mount bracket to generator mount plate.
  10. Install bolt to hold top of generator mount bracket to engine air intake plenum.
  11. Install accessory drive belt.
  12. Install windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  13. Connect battery negative cable.
  14. Verify generator charge rate.

Jan 02, 2011 | 2000 Plymouth Grand Voyager

1 Answer

How does the alternator bracket go on


Remove the accessory drive belt. Disconnect the negative battery cable. Disconnect the generator electrical connector. Remove the engine harness terminal from the generator: - Slide the boot back along the cable. - Remove the engine harness cable nut (3). - Remove the engine harness terminal from the stud. Remove the generator bolts and generator. Install the generator. Install the generator bolts. Tighten the generator bolts to 50 N?m (37 lb ft). Install the engine harness terminal to the generator: - Install the engine harness terminal to the stud. - Install the engine harness cable nut (3). Tighten Tighten the engine harness cable nut to 13 N?m (10 lb ft). - Slide the boot over the generator stud. Connect the generator electrical connector (1). Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure . Install the accessory drive belt

Dec 24, 2010 | 2001 Chevrolet Impala

1 Answer

Car not starting... Seems like battery isnt charging due to faulty alternator


did you have alternator and battery tested Disconnect the battery ground cable.

Remove the generator drive belt.
Release the tension on the drive belt.
Remove the drive belt from the generator pulley.

Disconnect the HO2 sensor harness clip from the generator bracket.

Position the generator bracket aside.
Remove the A/C line bracket bolt.
Remove the power steering pressure line bracket bolts.
Remove the generator bracket bolts.
Position the generator bracket aside.

Remove the generator bolts and position the generator aside.

Remove the generator.
Disconnect the two generator electrical connectors.
Remove the battery positive nut and washer.
Disconnect the battery positive cable and remove the generator.

Installation

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

To install, reverse the removal procedure.

Dec 18, 2010 | 1998 Ford Escort

1 Answer

96 f150 altenator rmovel instal


Section 14-02A: Generator, Integral Rear Mounted Regulator, Internal Fan Type, 95 Ampere and 130 Ampere 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/18/2000 Generator, 5.0L, 5.8L, 7.3L Engines Removal
  1. Disconnect battery ground cable (14301).
  1. Disconnect electrical connectors from generator (GEN) (10346).
  1. Remove drive belt (8620).
  1. Remove generator retaining bolts (3).
  1. Remove generator.


    Generator


    j6040a.gif


    Item Part Number Description 1 — Fuel Filter Assembly
    (Part of 9K601) 2 19703 A/C Compressor 3 8146 Fan Shroud 4 10A313 Generator Bracket 5 10346 Generator 6 389706-S2 Generator Retaining Bolts (3) 7 — Heater Hose Clip 8 — Heater Hose A — Tighten to 21-29 Nm
    (16-21 Lb-Ft)
Installation
  1. Install generator.
  1. Install generator retaining bolts (3). Tighten bolts to 21-29 Nm (16-21 lb-ft).
  1. Install drive belt.
  1. Connect electrical connectors to generator.
  1. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

    Connect battery ground cable.
2010&c18=modelyear&c35=wsm%2cgenerator%2c%205.0l%2c%205.8l%2c%207.3l%20engines%2cstj%2c14-02a%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=491&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Really need some help changeing alt on 2000 intrepid


  1. Disconnect negative battery cable.
  2. Raise and support vehicle.
  3. Remove lower plastic splash shield.
  4. Remove transmission cooler and reposition cooler out of the way.
  5. Remove lower radiator cross member support and position a jack stand under radiator for support.
  6. Loosen adjusting T-bolt, but do not remove.
  7. Loosen pivot bolt, but do not remove.
  8. Remove the generator drive belt.
  9. Disconnect the generator field circuit plug.
  10. Remove the B+ terminal nut and wire.
  11. Remove pivot bolt, being careful not to lose spacer.
  12. Remove generator.
INSTALLATION
  1. Install generator.
  2. Install pivot bolt, leave loose.
  3. Connect the generator field circuit plug.
  4. Install the B+ terminal nut and wire.
  5. Install the generator drive belt.
  6. Adjusting T-bolt and tighten belt.
  7. Remove jack stand from under radiator and install lower radiator cross member support.
  8. Reposition transmission cooler and tighten fasteners.
  9. Install lower plastic splash shield.
  10. Lower vehicle.
  11. Connect negative battery cable.

Jan 13, 2010 | 2000 Dodge Intrepid

1 Answer

Alternator removal 1998 ford taurus dohc


3.0L (4V)
Removal
  1. Disconnect the battery ground cable.
  1. Remove the accessory drive belt from the generator pulley.
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist.
  1. Remove the right front wheel.
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.

Nov 08, 2009 | 1998 Ford Taurus

1 Answer

How do you change the alternator on a 2002 toyota avaoln xls


Disconnect the battery before starting the job! Your power cable from the alternator will be disconnected and could potentially ground out if your battery is not disconnected!


  1. REMOVE DRIVE BELT Loosen the pivot bolt, adjusting lock bolt and adjusting bolt, and remove the drive belt.
00f6788.gif

  1. REMOVE GENERATOR
    1. Disconnect the generator connector.
    2. Remove the nut, and disconnect the generator wire.
    3. Disconnect the wire harness from the clip, unplug.
    4. Remove the pivot bolt, plate washer, adjusting lock bolt and generator.

5e50aad.gif

Please be sure to rate me if you find this information useful, thanks for using FixYa!

Sep 15, 2009 | 2002 Toyota Avalon

1 Answer

How to 1998 Taurus altenator R&R


please rate highly if this helps
Generator 3.0L (2V)
Removal
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  2. Remove the right front wheel. Refer to Section 00-02 .
  3. Remove the lower fender splash shield retainers and position the shield out of the way.
  4. Lower the vehicle.
  5. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  6. Remove the power steering line bracket and heater hose support bracket from the generator.
  7. Remove the upper generator bolts.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Disconnect the right hand stabilizer link.
  15. Lower the subframe to provide clearance.
  16. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Connect the right hand stabilizer link and torque to 47-62 Nm (35-46 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B + cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
3.0L (4V)
Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 14-01 .
  1. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  1. Remove the right front wheel. Refer to Section 00-02 .
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
3.4L (4V)
Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the right side cowl vent screen. Refer to Section 01-02 .
  1. Raise the vehicle and remove right front wheel assembly. Refer to Section 00-02 .
  1. Remove right tie-rod. Refer to Section 11-02 .
  1. Remove accessory drive belt (8620) from generator. Refer to Section 03-05 .
  1. Disconnect electrical harness connector and output terminal wiring.
  1. Remove nut and position engine control sensor wiring (12A581) out of the way.
  1. Remove the two bolts and one stud bolt.
  1. Remove generator from vehcile

May 12, 2009 | 1998 Ford Taurus

1 Answer

How to replace alternator on 98 chevy metro 4 cylinder


  1. Disconnect the negative (-) battery cable. CAUTION: Failure to observe Step 1 may result in a serious personal injury. It a tool is shorted at the generator lead, the tool will become hot enough to cause a serious burn .
  2. Remove the air cleaner assembly.
  3. Remove the rubber protector, the nut and the electrical connector from the generator B terminal.
  4. Remove the upper mounting bolt (1).
  5. Remove the drive belt.
  6. Remove the 2 lower generator mounting bolts.
  7. Remove the generator.
    1. Install the generator.
    2. Install the 2 lower mounting bolts finger-tight.
    3. Install the upper mounting bolt (1) finger-tight.
      1. Install the drive belt.
        • Adjust the drive belt to obtain a 68 mm (0.24-0.31 in) deflection with 10 kg (22 lbs) pressure exerted when reinstalling a used belt.
        • Adjust the drive belt to obtain a 5-7 mm (0.20-0.27 in) deflection with 10 kg (22 lbs) pressure exerted when reinstalling a new belt.
      1. Tighten the generator upper mounting bolt. NOTE : Refer to Fastener Notice in Cautions and Notices. Tighten Tighten the generator upper mounting bolt to 23 N.m (17 lb ft) .
      2. Tighten the generator lower mounting bolts.
      Tighten
      Tighten the generator lower mounting bolts to 23 N.m (17 lb ft) .
      1. Connect the electrical connector to the generator B terminal. Secure the connector with one nut and the rubber protector. Tighten Tighten the electrical connector nut to 8 N.m (71 lb in) .
      2. Install the air cleaner assembly.
      3. Connect the negative (-) battery cable. Tighten Tighten the negative (-) battery cable to 15 N.m (11 lb ft) .

Nov 18, 2008 | 1998 Chevrolet Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...