Question about Cars & Trucks

Open Question

How do adjust handbrake on hino fd ranger 07 - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the brake light switch located in a 1989 fd hino


If its a mechanical switch its on a bracket at the top of the brake pedal arm , if it is a pressure switch it located in the brake oil line near the master cylinder.

Mar 12, 2015 | Cars & Trucks

2 Answers

How do i adjust my handbrake on my freelander please


Here you go,,,follow what second post down says..yours is an F1 Freelander so it applies.
Land Rover Owner View topic Handbrake adjustment

Feb 25, 2015 | 2002 Land Rover Freelander

2 Answers

Handbrake cable adjustment


not 100% sure but think there is adjusting screw if you remove the rear ashtray

Apr 05, 2014 | 2005 Rover 45 1.6

1 Answer

How to set the handbrake


remove the rear wheels . adjust the cog up the way to tighten when the hub starts to drag move it down about two cogs on both sides.

Dec 20, 2013 | 2004 Ford Ranger

2 Answers

Ford transit 07 handbrake light not working


Wow- very complicated. No, many transits that age have no switch for the handbrake. I don't know why. But if you want to know where to find the switch so you can check yourself, you just pull up the handbrake cover and remove it. (Is rather stiff). There is a tounge on the leaver which should press a switch once the handbrake has come down to rest. The switch Is held onto the handbrake bracket by a small clip. Basically, if you remove the cover and you can't see an obvious wire / switch , you don't have one :-)

Feb 03, 2012 | Cars & Trucks

2 Answers

My handbrake needs adjusting in my Toyota Corolla 1994. Can u please explain how this adjustment is done.


Hello, My usual Brands are Ford products, but Foreign cars usually use simple, less expensive ways to do things. Assuming the brake pads are good, there should be a cable connected to the handbrake. You would usually pull the handbrake up to engage about 1/4 the way to engagement and lock it there.
Then you would go underneath the car and find the cable that stretches from the handbrake lever to a juction with a second cable. There should be an adjusting thread somewhere at this intersection.

With the rear wheels off the ground, you would tighten the nut on the threads of the handbrake cable until you hear rubbing in the rear brakes. Then get inside the car and pull back on the handbrake lever and you should not be able to move the rear wheels with the handbrake set. You then release the handbrake 100% and the rear wheels should turn mostly without noise.

Now if you can not find an adjustment nut under the car, it is possible the handbrake adjustment nut is under the handbrake cover/boot inside the car. Still use the same process of setting the lever 1/4 engaged and tightening the threaded cable until the rear wheels start dragging.

I hope this helps you.

Sep 28, 2011 | 1994 Toyota Corolla

1 Answer

Ford bantam handbrake adjustment


remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

May 31, 2010 | 2006 Ford Focus

1 Answer

How to adjust handbrake cable


HANDBRAKE CABLE ADJUSTMENT

1. Raise the vehicle and release the handbrake.
2. De-adjust the handbrake cable.
  • Remove the locking pin.
  • Slacken the adjuster locknut.
  • Slacken the adjuster until the levers on the callipers have returned to their stops.
3. Paint alignment lines on the lever and caliper
4. Tighten the adjuster until the caliper levers move from the alignment lines.
5. Apply the handbrake to equalise the cable.
6. Tighten the adjuster locknut to a minimum of three clicks and a maximum of six clicks.
7. Fit a new adjuster locking pin.
8. Lower the vehicle.

Jun 04, 2009 | 2002 Toyota MR2 Spyder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...