Question about 1999 Chrysler LHS

Open Question

How do I replace the ignation switch in my 1999 chysler LHS

Posted by Anonymous on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1997 Chrysler LHS,2339601/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528006ae93

Posted on Nov 03, 2008

  • 2984 Answers

SOURCE: need to replace the ignation switch in my 2000

Removal & Installation

  1. Disconnect negative cable from battery.
  2. Remove the Instrument Panel Center Bezel, Chrysler and Dodge.
  3. Remove side trim panel to steering column cover.
  4. Remove the screws that secure the steering column cover to the instrument panel and relocate panel.
  5. Pull the steering column cover rearward at the top and right side of the cover to release the snap retainers from the instrument panel.
  6. Remove the screws that secure the instrument panel steering column cover reinforcement to bracket and remove reinforcement from the vehicle. Remove the 2 front mounting nuts.
  7. Remove the lower mounting nut.
  8. Slide the assembly rearward into the instrument panel and down to gain access to switch.
  9. Disconnect the electrical connector from the ignition Switch and SKREEM Module.
  10. Remove the interlock cable by depressing the locking tab and pulling straight.
  11. Remove ignition switch mounting screw.
  12. Squeeze the 2 locking tabs to remove ignition switch from the lockhousing .

Removal and installation of the ignition switch

To install:

NOTE A tab on the ignition switch indexes to a notch in the lock cylinder housing. Also, a slot in the end of the ignition switch fits over the shaft in the end of the lock cylinder housing.

  1. Use the ignition key to rotate the lock cylinder to align the ignition switch with lock cylinder housing.
  2. Insert ignition switch into lock housing until locking tabs are seated into openings on lock housing.
  3. Install ignition switch mounting screw.
  4. Install the interlock cable into the switch assembly. Attach electrical connector to SKREEM Module.
  5. Install switch assembly into Instrument Panel.
  6. Attach electrical connector to ignition switch.
  7. Tighten the 2 mounting nuts.
  8. Tighten the lower mounting nut.
  9. Install steering column reinforcement.
  10. Steering column reinforcement installed.
  11. Install the Steering column reinforcement cover.
  12. Install trim panel end.
  13. Install the Bezel cluster.
  14. Install the ignition switch bezel ring.
  15. Connect the negative battery cable.

Posted on May 28, 2010

  • 474 Answers

SOURCE: I have a 1999 Chysler LHS and I want to disable

You can look in the owners manual and find the fuse that powers the reverse mirrorr action and pull it out.
That should fixya.

Posted on Feb 25, 2011

  • 3400 Answers

SOURCE: I have a 1999 Chysler LHS and I want to disable

Pull the power mirror fuse

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have 99 Chysler LHS it have a gas leak...easy

once you find what is leaking then you will know what needs to be replaced. until then the difficulty to fix is unknown. these have a plastic fuel line system instead of steal so unless your good at replacing things correctly this should be taken to a shop that has the tools to fix the line. for someone that is technically inclined its not difficult but to someone else it can be a hard fix and aggravating.

Sep 25, 2014 | 1999 Chrysler LHS

1 Answer

2000 chysler lhs 3.5 no computer grounds for my relays.

look for a loose / dirty earth wire connection from the body to the battery and from the engine to the battery. Check the earth wire terminal and battery post are shiny clean and tight.

Dec 22, 2013 | 1999 Chrysler LHS

1 Answer

2000 chysler LHS radiator drain plug WILL NOT DRAIN?

Could have sediment built up in the drain. Try a wire or compressed air to clear.

Dec 05, 2013 | 2000 Chrysler LHS

1 Answer

1997 chysler LHs timing belt.. #1 bank runing to rich.tooth off and 1-3 cylinders off which side is # one bank

Check, for 1997 Chrysler LHS 3.5 liter SOHC V-6 VIN "F"... bank #1 is refer at cylinder #1


Hope this helps.

Oct 01, 2011 | 1997 Chrysler LHS

2 Answers

I have a 1999 Chrysler LHS, Power Windows

yep master switch panel is shot!

Jan 14, 2010 | 1999 Chrysler LHS

1 Answer

How do you remove battery from a chysler LHS?

the right front tire has to be removed and a panel removed then one battery cable closest then slide the battery out partially then the other cable.

Aug 16, 2009 | 2000 Chrysler LHS

1 Answer

Low power to ignation switch

Check battery voltage with a volt meter. Voltage at ignition switch should match that of battery less 1% due to built in loss at connections and wire resistance. If not, check connections on the way to the switch, beginning at the battery to see where power drops off. Check all grounds as well.

Jun 02, 2009 | 1999 Jeep Cherokee

1 Answer

1997 Chrysler LHS,2339601/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528006ae93

Jun 24, 2008 | 1997 Chrysler LHS

Not finding what you are looking for?
1999 Chrysler LHS Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides