Question about 2003 Dodge Intrepid

Open Question

2003 Dodge Intrepid code P1698. Speedometer not working and transmission is in limp mode.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

polarcycle
  • 1392 Answers

SOURCE: 98 Intrepid Gone into "Limp Mode"

There are some sensors on the transmission that tend to go bad. You may also need to check the wiring. Could be a computer problem. How many miles?

Posted on Mar 06, 2009

  • 323 Answers

SOURCE: limp mode?

It may have a "loss of prime" code that usually follows a service of the fluid and filter. After you're sure the fluid is full at operating temperature, disconnect the battery for a few minutes and reconnect to see if the code resets. I hope this helps.

Posted on Apr 26, 2009

  • 8 Answers

SOURCE: 1997 Dodge Intrepid transmission slipping when warm

I was told to change my Transmission Control Module,located on the transmission . You can get it new for under $200 but, I was advised to get it from a junk yard it's alot cheaper and its easier. I hope this helps

Posted on May 07, 2009

  • 412 Answers

SOURCE: 2000 Dodge Intrepid. Replaced battery, speedometer stopped.

YOU NEED TO HAVE ENGINE CONTROLLER AND TRANS CONTROLLER SCANNED FOR FAULT CODES..LOOK FOR SPEED SENSOR FAULT CODES(OUTPUT)OR VEHICLE SPEED SENSOR FAULT CODES..IF SO..AN OUTPUT SPEED SENSOR WOULD BE GOOD PLACE TO START..LOCATED ON LEFT SIDE OF TRANS..FARTHEST ONE BACK..SCREWS INTO TRANS..ABOUT 40 BUCKS AT DEALER..HAVE CHANGED LOTS OF THEM..IF DOESN'T HELP,LET ME KNOW WHAT FAULTS ARE PRESENT

Posted on Aug 01, 2009

  • 312 Answers

SOURCE: Chrysler intrepid 2003 obd 2 code P0441

Most common problem causing this code is the purge solenoid. A quick smoke test will show if you have any leaks in the system. If no leaks and the fuel cap is installed properly it's the purge solenoid.

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 dodge startus transmission wont shift, speedometer works, engine light is on. Need help?


Transmission is in limp mode. This enables you to drive the car to service. Anytime there is a transmission code in the computer even if nothing is wrong it will stay in limp mode until the code is erased. Most retail auto parts stores will run an obd2 diagnostic scan to determine the problem and erase existing codes, no charge (Auto Zone, Advance and others)

May 14, 2014 | 2001 Dodge Stratus

1 Answer

Speedometer quit on a 2000 intrepid. And it quit shifting gears at the same time


A common issue are the input and output speed sensors.When bad they cause the vehicle to go into limp mode keeping it in second gear and speedometer sometimes no longer works.

Jul 06, 2010 | 2000 Dodge Intrepid

2 Answers

99 Dodge caravan - Check engine light on, limp mode, no speedometer. What's up with this trusted friend?


Its very possible that the transmission output speed sensor has gone bad. The output speed sensor is what the speedometer reads for vehicle speed. When you open the hood and look straight down at the front of the transmission you will see two sensors that screw into the side of the transmission case that are about the size of a half dollar, the output speed sensor will be the one on the far right side.

Mar 14, 2010 | 2005 Dodge Grand Caravan

1 Answer

When i slow down the trans shifts hard and stays locked in 1st or 2nd gear untill i restart the car it is a 2003 dodge intrepid 2.7


This is called a 2nd gear limp mode -- it is a safety devise in the computor to prevent interior damage to the transmission -- the cause could be a speed sensor or a blown rear low/reverse seal inside the transmission.

Jan 08, 2010 | 2003 Dodge Intrepid

1 Answer

1998 Chrysler Intrepid ES 3.2 Code P0731.


Check the connection to the vehicle speed sensor. You can check the vehicle speed sensor by using a voltmeter set at millivolt. Then pass a metallic object close to it. The sensor should induce voltage as you pass the metallic object close to it. If not replace the vehicle speed sensor.

Nov 23, 2009 | 1998 Dodge Intrepid

2 Answers

2003 Chrysler Intrepid Sensor reads P0700


P0700 is a code in the engine computer telling you that you have codes in the transmission computer. You need to have the transmission computer scanned.

Jun 21, 2009 | 2003 Dodge Intrepid

1 Answer

1995 intrepid


This sounds like a VSS (vehicle speed sensor) problem, have the code(s) retrieved from the powertain control module and see if that code comes up.

Oct 21, 2008 | 1994 Dodge Intrepid

7 Answers

2002 Dodge Intrepid transmission not shifting


Flush out your transmission with the correct type fluid, Mopar ATF+4, and correct filter. Disconnect Negative cable, to reset computer, for at least 24 hours. Check grounding straps for PCM, ensure they are tight and clean.
This method worked on my 2003 Intrepid SE, 3.5L, Police Pkg car.
Good Luck!!

Jun 27, 2008 | 1997 Dodge Intrepid

Not finding what you are looking for?
2003 Dodge Intrepid Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...