Question about 1995 Isuzu Rodeo

Open Question

My truck run but wont go into gear manual transmission

When the trck is on it won't go into gear clutch is working an there is transmission fluid in my gear box?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: I just recently was given

if you have hydro fluid in the clutch master cylinder and the system is free of air, then it needs a clutch

Posted on Feb 02, 2009

  • 701 Answers

SOURCE: 1995 isuzu trooper manual transmission

Hello smeet3992: The transmission uses 5w-30 for tempretures up to 95 degreese in tempreture. Uses 15w-40 for all tempretures greater then 50 degreese. If you are in an area that has extreme fluctuation in tempretures I would use the 15w-4o engine oil. I also senrt a picture of where to check the oil at. Make sure you pull the right plug. The reverse idler pin has the same size bolt head.
Please rate the quality of your answer as this helps to ensure you recieved the information you asked for. Thank You for using FixYa. Roger358a4b4.jpg

Posted on Apr 24, 2009

  • 232 Answers

SOURCE: clutch or transmission?

If its automatic follow this link.

Posted on May 11, 2009

wireguy212
  • 1627 Answers

SOURCE: manual transmission wont go into gear unless

if you have to shut off the car to get it in gear then you either need to adjust the clutch or repair the slave cylinder.check your fluid level for the clutch,owners manual will tell you how.

Posted on Aug 23, 2009

Transdoc
  • 829 Answers

SOURCE: 92'isuzu pick-up, 2.3L.manual tran. the truck

Yes it is time to install a new clutch kit(clutch disc,pressure plate ,throw out bearing and pilot bearing)also have the flywheel resurfaced.The disc has gotten too thin to be clamped by the pressure plate.Best if you replace everything at once with new parts,avoid rebuilt parts.Good luck!

Posted on Mar 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 94 Toyota celiac stars up but when I put in gear it won't move


Most possible ur transmission clutch r out.. if transmission fluid too low n u run it for sometimes the internal pump n the torque converter will damage too..

Apr 02, 2013 | 1994 Toyota Celica

1 Answer

5-Speed transmission;Won't shift into gear.


If you can shift it with car off, but not with engine running, it is a clutch poroblem. Check the fluid level in the clutch master cylinder on the firewall next to the brake master cylinder. If it won't shift with engine off, either the shift linkage is binding, or there is an internal problem in the transmission.

Jan 15, 2013 | 1992 Daihatsu Rocky

2 Answers

My 1998 Ford Explorer Sport Manual Transmission won't shift into any gear


Then there is a serious problem with the clutch. turn the engine off and engage a gear and try and roll the truck, do it feel like it is in gear? if not the clutch is either defective or the transmission input shaft is broken

Oct 12, 2012 | Cars & Trucks

1 Answer

1995 eagle talon manual transmission i'm able to put my clutch down and shift gears, but car wont accelerate


Something is broken, that is for sure, pull the transmission out and first look at the clutch plate.

Jul 08, 2012 | 1995 Eagle Talon

1 Answer

Wont go into gear


Did any fluid come out? It has to have fluid reach the slave cylinder, and when bleed valve is open and clutch is pressed, fluid should squirt out. Open the valve and pump the clutch until fluid is forced down into the slave cylinder. Keep topping up the clutch master cylinder so it won't run dry.
Post back if still having problems. There is a tool at auto parts stores for pressure bleeding brake lines and clutch lines. It forces fluid into the lines by pressure. If nothing works, your clutch master cylinder may have failed. Take the line off at the slave cylinder and see if the master cylinder is working to push fluid through the line.

May 10, 2012 | Hyundai Motor 1997 Tiburon

2 Answers

Pickup starts great, goes into all gears but won't move. It's like it is still in nutural.


Assuming the pickup is an automatic, check the transmission fluid. The #1 cause for transmission slippage is lack of Automatic Transmission Fluid.

If the pickup is a standard shift, the pin that connects the shift to the transmission has likely broken. You would still be able to shift from the inside but the gears won't engage. A bad clutch is also a possibility but you would have noticed a burning smell prior to the clutch giving out.

Dec 20, 2011 | Cars & Trucks

1 Answer

My 1998 Honda civic ex won't move but the motor


Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

2 Answers

I have a 99 gmc sonoma that won't go into gear and there is no presure on the clutch pedal it goes straight to the floor but the fluid level is still on full and the fluid has some black looking gunk...


It is confirmed that the clutch hydraulics has faulted. Since there is no clutch the gear links are not engaged. Possible that the master cylinder has failed, possible a leak in the system.
You will need to overhaul this section and the pedal will respond.
Also check on the transmission fluid and the gear settings.

Sep 30, 2011 | 1999 GMC Sonoma

1 Answer

Why wont car shift into gear


Hello and welcome to FixYa!

You may want to start adjusting the brake pedals. If it detects that you are not stepping on the brake then it won't shift into gear.
If the gear is moving but won't shift gears while running then you may want to start on replacing the transmission fluid. It can be burnt that's why it's not operating properly.
Hope this helps and thank you for using FixYa! Have a good one!

Aug 14, 2011 | 1997 Ford Escort

1 Answer

Manual transmission wont go into gear unless engine is off. Starts fine, air runs. Feels like it is locked out of gear. Don't know if it is clutch or transmission


if you have to shut off the car to get it in gear then you either need to adjust the clutch or repair the slave cylinder.check your fluid level for the clutch,owners manual will tell you how.

Aug 23, 2009 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1995 Isuzu Rodeo Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...