Question about 1999 Dodge Neon

1 Answer

Window on 1999 Dodge Neon has broken brackets on track

I want to replace the broken brackets, but it is difficult to see how mechanisms work.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Dodge Expert
  • 405 Answers

Take door panel off, inside door is window regulator. Window removed, it is 2 tracks and a motor, replace the whole unit, GOOD LUCK!!

Posted on Mar 05, 2015

6 Suggested Answers

leetamara
  • 702 Answers

SOURCE: removing a starter

Yes, you'll have to remove the bracket.

Posted on Jun 30, 2008

  • 59 Answers

SOURCE: Broken rear slideing glass window on a dodge dakota 2001.

on this truck the rear window is glued in with urethane, if I was cutting it out I would use a special power tool designed to do this. I am sorry but this will not be easy with out it, the only thing I could see is you bending and cut the frame off with a scraper and hammer. (bad picture in my mind) might be worth a stop at an auto glass shop and ask them to remove.

Posted on Feb 27, 2009

  • 8 Answers

SOURCE: fuse for the rear window defroster on the Dodge Neon

ok dude.... simpe questioneasy answer is 10. in the position#EIGHT

Posted on Mar 12, 2009

  • 398 Answers

SOURCE: Passenger side mirror replacement

you should be able to take it off from the inside of the car directly behind were the mirror is. usually ther eis a molding cover ing the mounting screws . take off the molding , mabey a few screw then some body clips that just snap off. now you should unplug the harness if necessary and remove the three or four bolts that hold the mirror on, and that should be it. hope this helps

Posted on May 17, 2009

techbuster
  • 5081 Answers

SOURCE: 1999 Dodge Neon rear license Plate bulb

LICENSE PLATE LAMP BULB
REMOVAL

  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Posted on Oct 08, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge 1999 neon headlight broken something is broken


dont tack it back cause they will say that you broke it and you fixed it. just try and replace the light housing and your plug

Jan 18, 2014 | 1999 Dodge Neon

1 Answer

Power windows


You have to replace the broken Window Regulator

The entire cable assy & broken item

Aug 22, 2013 | 2004 Dodge Dakota

1 Answer

Dodge Neon Passenger Window off track


You have to remove the inner door panel, End then put it back into the track,

Nov 04, 2012 | 2003 Dodge Neon

1 Answer

Walking camshaft on 99 dodge neon


  • 1 Park your Neon on a level surface. Engage the parking brake. Open the hood and loosen the bolt on the negative battery cable terminal and pull the cable from the battery.

  • 2

    Remove the Neon air filter by undoing the side clips and lifting the cover of the air filter off. Pull the air filter from the bracket. Undo the clip on the air filter hose and pull the hose off the inlet. Use a socket wrench to loosen and remove the four bolts holding the air filter bracket in place and pull the bracket from the engine

    3

  • Locate the camshaft position sensor. It will be at the rear of the cylinder head, centered on where the air filter housing was about midway down. It will look like a black plastic square (4"x4") and have four bolts holding it to the engine.

  • 4

    Disconnect the wiring of the sensor from the wiring harness feeding into the car's electrical system. Press in the tabs at the sides of the connector and pull the two halves apart to do this.

  • 5

    Remove the four bolts holding the sensor in place and remove the sensor from the engine.

  • 6

    Clean the engine of any gasket material from the old sensor by scraping the surface gently with a paint scraper.

  • 7

    Install the new sensor by placing it in the same position as the old one, replacing the bolts and then connecting the wiring harness. Replace the air filter bracket, hose, filter and cover. Reconnect your battery and you are done.



  • buy F150 Parts.

Jun 03, 2012 | 1999 Dodge Neon

2 Answers

Change Power Windows motor 2000 Dodge Neon


you will have to remove the interior door trim to gain access to the inside of the door.
i am not sure of the setup in your door but if it is cable driven you may have to replace the whole winder mechanism as I think they come as a unit.
If it is pop riveted to the door panel you will have to drill the rivets out and replace with new ones
Have a good look or take a pic at how it is mounted b4 you start pulling it down

Jun 12, 2010 | 2000 Dodge Neon

1 Answer

How to replace power window motor for 2003 dodge


That's unusual for a window motor to go bad, however the plastic track breaks causing the window to become inoperative. If you hear the window motor working, then the plastic geared strip is probably broken. It would be cost effective to you to first find out whether the plastic track is broken for now Chrysler sells a "generic" window track where you cut the plastic track to fit Your Vehicle. Should this be the case, then remove the door panel (a Haynes Manual would come in handy), and take out one pin in the plastic track, while supporting the Window! (smile) and remove the old track and re-install the new track.

A little secret here...buy some Mopar Speedometer Grease while buying the Window Track and grease the metal rail that the plastic track rides on. The Speedometer grease is NOT temperature sensitive, so it works well in Summer & Winter Temperatures.

Should it truly be your Window Motor, Chrysler sells a re-build kit for the Window Motor which has the gears and grease needed to replace the worn out ones in the head of the Window Motor rather than paying for a "Brand New" window motor. All of this (the plastic window track AND the Window Motor Kit), will be under $100.

I hope this helps you,
Let me know if this resolves your problem.

"00 Buck"

"Still living on the Right Side of Dirt..."

Jun 04, 2010 | 2005 Dodge Grand Caravan

1 Answer

Window wont go back in place


sounds to be like you do not have it in its track on the inside of your door. It must be fully on track to work properly. Also check to make sure they did not bend your mechanism which brings your window up and down along with the tracks may be out of line.

Oct 06, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

The rear passenger side window seems to be coming off at the front side. I can tell if the rubber is torn or if it just need to be pushed back together.


sounds like the track has been dismounted....try to pull off the inside door panel and look for any missing or broken bolts on the track itself... the track protrudes down to keep the window on track....if this is not a problem look at the glass itself...roll the window down a little to see the bottom of the glass. makes sure all of the mounting brackets are in place and secure..

Aug 12, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Passenger window not always going up or down


replace the window regulator and the problem will be fixed

Jun 04, 2009 | 1999 Dodge Caravan

2 Answers

1999 Dodge Neon R/T hand Brake


You have a broken cable, or one of its parts. You need to trace the cable from the "pull" back to where it splits to go to the left and right rear brakes, and finally to each rear brake. You will most likely need to get under the vehicle and for this you will need to jack it up. Please be safe, or if uncomfortable, take to a trained mechanic, that should be able to fix this for very little money.

If you choose to go it yourself, please check out this article.

Regards,

Brian

Sep 15, 2008 | 1999 Dodge Neon

Not finding what you are looking for?
1999 Dodge Neon Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...