Question about 2001 Honda Odyssey

1 Answer

Rear window wiper is not sweeping but is spraying

Wiper is not moving when i turn on switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

What more proplemHonda odyssey like check ingine tcs sbs please I need help

Posted on Nov 27, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: 1996 Honda Civic Wiper Spray problems

You will not be able to tell whether the spray nozzle is clean just by looking at it.
Poke it with a fine needle and keep trying to spray. If it is blacked,it will soon clear up.
I take it you can hear the spray motor running when you depress the switch.

Posted on Nov 11, 2008

  • 1 Answer

SOURCE: odyssey rear window washer fluid not spraying where is reservior

The reservoir is the same one for the front washers. There are two electric pumps on the base of the reservoir (one for front and one for rear). You probably need a new pump. It is accessible behind the panel in front of the front right wheel.

Posted on Jan 31, 2009

  • 2973 Answers

SOURCE: My rear windshield wiper operates

Please remove the wiper arm from the motor by unscrewing the bolt holding it there and re-fix it in 180 degrees direction or whatever suits your car. That adjustment would have to made by you being the person on ground.

Posted on Sep 19, 2010

  • 50 Answers

SOURCE: my rear window wiper is not sweeping when i turn on the switch, but it is spraying

sounds like the wiper motor either went bad or it is somehow stuck on something or something is stuck on it. most likely just a bad wiper motor which should be an easy fix and not to expensive. good luck

Posted on Apr 20, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it my 2008 chevy uplander rear wiper motor/blade moves some and stops. I let van set 5-10 minutes with key off. Turn on key. Wiper motor/blade moves a few degrees and then stops again. Why?


Can you move the wiper by hand ? Which does your vehicle have ?
WDA/Z88 The rear wiper is controlled based on an input from the rear wiper/washer portion of the multifunction switch. When closed, the wiper ON and wiper DELAY switches provide a unique voltage signal to the rear window wiper motor indicating the desired speed. Each switch has a unique resistor that drops the voltage to a specified value which is interpreted by the rear window wiper motor as ON or DELAY. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
W49 The rear wiper is controlled based on an input from the rear wiper/washer switch. When closed, the wiper ON switch provides a voltage signal to the rear window wiper motor indicating rear wiper operation is requested. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
Do you know how to do electrical testing ?
WDA/Z88
  1. Ignition OFF, disconnect the harness connector X1 at the multifunction switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 4 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the multifunction switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, test for B+ between the signal circuit terminal D and ground.
  12. ?‡'
    If less than the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, test or replace the multifunction switch.

  13. Rear wiper switch in the DELAY position, test for B+ between the signal circuit terminal D and ground.
  14. ?‡'
    If less than the specified value, test or replace the multifunction switch.

  15. If all circuits test normal, test or replace the rear window wiper motor.
W49
  1. Ignition OFF, disconnect the harness connector at the rear wiper switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the rear wiper switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, verify a test lamp illuminates between the signal circuit terminal D and ground.
  12. ?‡'
    If the test lamp does not illuminate, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the I/P switch assembly.

  13. If all circuits test normal, test or replace the rear window wiper motor.
Component Testing

Do you know how

Jun 09, 2016 | 2008 Chevrolet Chevrolet Uplander LS

2 Answers

Jeep wrangler wiper fluid will not dispense on front windsheld but will on the rear


Switch is faulty is the first thing comes to my mind. Your spot on tho in your diagnosis, although you may have two pumps and tanks, one for front, one for rear. I would check all my fuses just to be sure, and I would look at all my waster tubes and make sure they are not clogged, check your nozzles too, as sometimes wax can clog them up.

Dec 16, 2013 | 2008 Jeep Wrangler Rubicon

1 Answer

My rear window wiper is not sweeping when i turn on the switch, but it is spraying


sounds like the wiper motor either went bad or it is somehow stuck on something or something is stuck on it. most likely just a bad wiper motor which should be an easy fix and not to expensive. good luck

Apr 20, 2013 | 2001 Honda Odyssey

2 Answers

When I pull back wiper lever to spray windshield, wipers move but do not spray windshield. When I turn wiper lever end forward to spray rear window, it sprays front windshield. How is this possible?


Possible there is fault in the cluster switch , possible that the switch is not contacting according to the intended function to power the front washer and rear washer motors.
You need to check the output or using a multimeter the switch continuity of the wiper cluster switch.

Apr 04, 2011 | 2003 Pontiac Vibe

1 Answer

The rear window wiper and window water spray will not turn off


This sounds like a bad switch, try dissconnecting the switch for the rear wipers and see if it stops if it does then replace the switch, the motor is pretty get and dry if it runs and the sprayers spray then it sounds like the switch is stuck or bad.start there,

Jul 20, 2010 | 1990 Plymouth Voyager

2 Answers

Rear window washer does not spray fluid. When I push the rear window washer button, the front washer/wipers turn on. The rear wipers work normally.


I have the same problem with my 2000 chevy blazer as skornec had posted. I kinda already figured the hose or spray nozzle was plugged. But the problem with checking those items is that I don't know where the hose is located to the back wiper. And the only thing that could be I see that could be the spray nozzle doesn't even have holes that washer fluid could spray from. So basically I just would LOVE if someone could please inform this lame brain of where to find the spray nozzle on the rear window and where in the interior of my blazer does the washer hose run.

Apr 02, 2010 | 2000 Hyundai Accent

1 Answer

My 07 nissan murano rear windshield wiper doesn't work properly it goes the wrong way, not on the window.


You need to adjust the wiper arm location. Loosen the 12 mm or 10 mm nut that holds the rear wiper arm. Wiggle the arm until it comes off. Then turn on the rear wiper for a second and turn it off, leaving the key on. This way the rear wiper motor will do it's sweep, and them park where it's suppose to. Then reattach the rear wiper arm and secure the nut and recheck.

Thanks Jay!

Jul 20, 2009 | 2007 Nissan Murano SE

1 Answer

Rear window wiper


probably rusted inside. find a replacement or open it up and see if you can spray some lube in there. usually helps.

Mar 12, 2009 | 1986 Volkswagen GTI

2 Answers

Rear wiper linkge BMWe46 touring 2003 year


Not sure about this exact car but 99% of all wiper motors are retained with a nut ythart lives under the base of the wiper arm and with three or 4 nuts from the rear of the motor. Take the wiper arm off, possibly requiring the use of a 10 mm wrench, and you will see a large nut, remove this. See if the wioper mote is accessed from the trunk, most likly under a clip in panal, split the electrical connector and remove the nuts holding the motor on. You will see that the collar that had the nut accessed from above will be stiff to move on the wiper shaft. Work it off, scotch brite the shaft, run a small wire brush down the typically plastic tube, lube the shaft with chassis grease or white grease, check that it moves freely in the collar and reassemble

good luck

Feb 06, 2009 | 1999 BMW 318 ti

Not finding what you are looking for?
2001 Honda Odyssey Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...