Question about Cars & Trucks
Timing belt marks 2.4 petrol triton
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: geo metro timing diagram
woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck
Posted on Jan 29, 2009
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
Posted on May 06, 2009
SOURCE: 1999 kia sportage timing marks
Crankshaft match marks
Align marks on timing belt pulley and pump body.
Camshaft pulley alignment marks
Posted on Jul 26, 2009
1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cyl
Fig. Timing belt and components-2.0L engine
Fig. Location and correct alignment of timing marks for the timing belt (camshaft)
Fig. Timing marks-2.3L diesel engine
Fig. Timing marks-2.4L engine
More details, autozone.com (free register). Good luck.
Posted on Sep 29, 2009
Tips for a great answer:
May 03, 2017 | Hyundai Cars & Trucks
Mar 08, 2017 | Cars & Trucks
Dec 10, 2015 | 2002 Land Rover Freelander
Dec 27, 2014 | Vauxhall Cars & Trucks
May 31, 2014 | 2005 Suzuki Forenza
Nov 27, 2013 | 2005 Suzuki Forenza
Sep 13, 2012 | 2005 Audi A8
May 30, 2012 | Cars & Trucks
Nov 22, 2009 | 2005 Kia Spectra
Mar 28, 2009 | 2004 Mitsubishi Outlander
91 people viewed this question
Usually answered in minutes!