Question about 1999 Chevrolet Lumina

1 Answer

1999 Chevy lumina hazard lights do not work

The hazard lights do not work. the switch is broken and has to be pressed with a screw driver. When the switch is activated the dash turn signal lights do not light up and the exterior lights do not work. When the switch is not depressed the running lights, brake lights and turn signals work except the left rear blinker is intermittant but i believe that is due to a malfunctioning muli-function switch due to the fact i can make it work by gently pulling on the switch. Thanks for your help

Posted by on



1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

Most likely need new muli-function switch

Posted on May 29, 2017


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 508 Answers

SOURCE: right signal and brake light

Looks like the problem is in the turn signal switch. This is a common problem. When the turn signal switch goes bad it will cause problems as mentioned above by you. Replace the turn signal mechanism.

Posted on Feb 25, 2009

  • 1632 Answers

SOURCE: 1999 ford crown vic dash light running light problem.

Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.

Posted on Sep 09, 2009

Testimonial: "thank you for quick response will try all of your suggestions will re post if no luck."

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2013 GMC Sierra 1500. Where is the signal light control module LM487 located? I have the knee bolster off but still can't locate it.

signal light control module LM487 ???? How did you come up with this ??? Your vehicles BCM - body control module controls the hazard an turn signals . Turn Signal/Hazard Lamps
When the turn signal switch is placed in either the left or right position, a ground signal is completed from the turn signal switch to the BCM. When the hazard flasher switch is activated, a ground signal is completed from the turn signal/hazard switch to the BCM. The BCM then sends an ON-OFF voltage signal through the fuses to the appropriate turn signal and side repeater (export only) lamps or to all of the turn signal fuses for hazard operation. The driver door switch and passenger door switch also receive voltage from the BCM turn signal supply voltage circuits for the mirror turn signals. The door switches have no function or control of the mirror turn signals other than a pass through connection for the circuits. The audio chime is also activated when the turn signals are ON. The instrument panel cluster (IPC) receives the signals to activate the turn signal indicators over the GMLAN serial data system. When the hazard switch is pressed, all turn signal lamps will flash including both IPC turn indicators.
Your best bet , take it to a qualified repair shop .

Nov 29, 2017 | GMC Sierra 1500 Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville

I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

I have a 2005 325ci bmw the hazzard light not working neither turn signal .

The simple, and most likely, cause of this problem is a blown fuse in the turn signal circuit. Normally, the turn signal lamps are activated by a single-pole double-throw switch circuit on your 325ci's steering column. That switch is also called turn signal switch and, as you know, you activate it by pressing up or down on the turnstalk (the lever usually on the left side of the steering wheel).

The hazard light circuit is a double-pole single-throw circuit that gangs the right and left turn signal circuits into one and then activates the front and rear signals as your 325ci's hazard lights.

Since they use the same circuits, the fuse is common to both and if it is blown then neither the turn signals nor the hazard lights will work.

Jan 03, 2015 | Cars & Trucks

2 Answers

Chrysler Vision hazard light

on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

1999 chevy lumina headlight

There should be a fuse for the dash lights and one for the tail lights.
A mechanic would check for voltage for each circuit at the headlight switch and go from there.

Jul 02, 2012 | 1999 Chevrolet Lumina

1 Answer

I have a 90 montero and the brake lights and turn signals stopped working and I have replaced the fuses and can't figure it out.

my 91 Montero did the same thing, I finally traced it to a bad rocker switch for hazard lights. The switch was broken and it messed up brakes and turn signals. Check your switches that they work and rock properly. My hazard switch was binding turning on and off causing a short. Got a new hazard switch that worked freely and suddenly everything worked right. The problem drove me crazy, and I did replace the turn signal lever assembly first, brake switch, turn signal relay. I found dash switches on eBay.

May 22, 2012 | 1990 Mitsubishi Montero

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.

First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

Not finding what you are looking for?
1999 Chevrolet Lumina Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides