Question about 1992 Lexus Es 300

Open Question

92LEXUS ES300 HEAD GASKET REPLACEMENT DIAGRAM FOR REPAIR

NEED TOURQE SPECS,AND VALVE SETTING SPECS AFTER REPLACEMENT

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnjohn2
  • 5763 Answers

SOURCE: Im replacing the head gasket on my 94 GS300 and

step # 1 tighten 25 ft lbs,
step# 2 tighten 90%
step # 3 tighten another 90%
note do in sequence start closest to belt one head at a time start at the bottom 1 then to the top all the way to the other side is 2 then back to other side on top now is 3 then back to other side bottom is 4 keep do this working your way to the center do this with each step thats the sequence. hope this helps. note thses are strech bolts use new ones dont reuse old ones, put a little oil on threads. good luck.

Posted on Nov 29, 2009

Testimonial: "Thank you. You dont know how long I've been looking for solutions to this damn car."

  • 209 Answers

SOURCE: valve cover gasket leak on 95 lexus es300. how do

Take the valve cover bolts off then get the new gasket on or use permatex gasket glue than put it back together

Posted on Apr 10, 2010

mecanica03
  • 874 Answers

SOURCE: how to change valve cover gasket and thermostat on

the thermostat its located in water out hose near to a/c compressor, to change valve cover, front of engine remove the plastic cover with lexus logo using hex 5mm key 2 bolts , unplug 3 spark plug wires ,loose all 10mm bolts on valve cover , to rear engine valve cover remove before the manifold intake and all components , air filter duct , etc.

Posted on Aug 06, 2010

  • 1 Answer

SOURCE: need timing marks for belt replacment for a

need diagram for 1992 lexus es 300

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 1985 chevy s10 2.5 head gasket


Hi Sarah,here's a Autozone repair guide to your head gasket replacement. Repair Guides Engine Mechanical Cylinder Head AutoZone com

Apr 02, 2017 | Cars & Trucks

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

Need tourqe specs for 96 grand Cherokee loreado str 6 valves and cover


Cylinder Head Cover Bolts . . . . . . . . . . . . . . . . . . . . .10 N·m (85 in. lbs.)
85 in. lbs = 7 ft. lbs

Basically... snug, not tight. Don't want to crush the gasket.

Nov 03, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Toyota 2kd engine cylinder head tighten tourqe in n-m


Valve clearance is .20mm for the intake and .30mm for the exhaust.
The minimum diameter specs are: 11.6 mm for head bolts, and 12.6 mm for main bearing bolts.

Jul 10, 2013 | Cars & Trucks

1 Answer

I have coolant coming to my egr valve after i did a head gasket replacement


This can occur if the head bolts were not torgued to specs. For details

I use and I'd recommend you register for free at www.autozone.com Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Jun 28, 2011 | 2000 Ford Taurus

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

Need tourqe setting for head and intake bolts on 2000 land rover 4.0


Well, remembering that the head bolts are stretch bolts, which you tighten to 20nm (15lbf.ft) then turn 90 degrees, then a further 90 degrees :)
The inlet manifold you initially tighten them to 10Nm (7lbf.ft), then it says for the gasket clamp bolts you do those to 18Nm (13lbf.ft) and finally to 51Nm (38lbf.ft)

Feb 28, 2010 | 2000 Land Rover Discovery

1 Answer

I need to change the valve cover gaskets on a 1996


Valve covers are simple (if you have easy access). They normally have about 8-10 bolts surrounding the gasket. Remove these bolts and it comes right off. Remove the old gasket (do not use razor) with putty knife or gasket remover then install the new one. Usually specs are about 20-25ft lbs. You snug them not torque the bolts. The gasket does all the sealing.

Aug 28, 2009 | 1996 Dodge Stratus

1 Answer

Head gasket?


You remove air filter and other parts.
Then you remove head cover.
Then you unscrew and remove the head,
Clean a bit the block
Replace gasket.
Screw back the head
Follow head tourqe settings and screw orders on diagrams when mounting back the head.

The whole thing is not thst easy as it may seem, if you want to DIY you will need to buy the Haynes manual for your car. There you find a step by step procedure with pictures.

Here is a repair manual.

Also enquiry to Haynes.Haynes manuals are the best.

Here is how to replace head gasket on a Honda,
with lots of pics, procedure is the same, torque values and screwing order are different. It is not a job for absolute beginners


Do not forget to rate the solution

Thanks.

Aug 31, 2008 | 2000 Daewoo Leganza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...