Question about 1989 Toyota Camry

1 Answer

Engine check light keeps comming on

Whenevre i start my car as soon as i press the gass to move
the check light comes on

Posted by on

  • nalet01 Mar 12, 2009

    Thanks ill try your method

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

It may be your car may be due a service, at which point it can be reset. failing this i dont know, but the engine management light covers quite a few things

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stalls


Check engine light---scan for the fault codes. Go to your mechanic, or your local auto parts superstore. Most stores do it for free.

Apr 02, 2010 | 2003 Mercury Marauder

1 Answer

Ford focus 1.6 52 reg radiator fan comes on as soon as car is started from cold? is this normal


no the fan shouldent check that you ac is off as the fan comes on with the ac you can check the ford fault codes without going to a maindealer follow the instructions i am giving you
press the trip button and hold while turning the key starting the engine keep the tripbutton pressed for about 10 seconds then release the next time you press it it will do a sweep test of all gauges and dash lights the next time you press it it will then give differant bits of information flow rates oil flow and any fault codes

Mar 19, 2010 | 2000 Ford Focus

1 Answer

Electronic throttle control light comes on,car starts to idle rough and rpm hand went up


I am not to sure but I know that there is a process called the "Relearn" which mainly zinchronizes the throttle body with your ECU... But I am not to sure for a ford exactly I know that for a Nissan if you getting code P0507 the relearn Process will follow as: 1. Warm up the car to normal temperature of drive it for a few minutes and turn it off. 2. After you shut off the engine wait ten seconds. 3. Turn the Key to the ON Position but don't start the car. 4. Wait 3 seconds and press the gass pedal and release 5 times in whitin 5 Seconds. 5. Give it a 7 seconds and press the gas pedal and keep it pressed for about 10-15 seconds and the engine light should star blinking for about 15-20 seconds as soon as it stops blinking start the engine let it run for about 20 seconds and rev the engine up a couple of times then you can shut it off.
But I had a couple of time in which a rebuild piece might fail to sync with the relearn process...You might need to go with a new part....Good Luck. I am kind of sure that Ford migh have a forum those sites are very helpful because of they are Ford Vehicles owners that will post their solutions to similar issues.


Good Luck! CR.

Mar 15, 2010 | 2006 Ford Mustang

3 Answers

Dies when started cant find check engine light


The service engine light is the check engine light. Different name for the same thing.

Feb 22, 2010 | 2002 Ford E350

2 Answers

Service engine soon light keeps comming on


Have had the car serviced lately? Oil change, tune up, things of that nature? It may be time to do that stuff. Does that car have a "Service Engine Soon" light and a "Check Engine" light? If the car has been serviced recently and the "Service Engine Soon" light is coming on, it's because who ever serviced it, did not reset the light. To reset the light, this works on most GM cars, turn the ignition to the "on" position DO NOT START THE CAR!!! Now within 5 seconds push the gas pedal to the floor and release it 3 times. That should reset the light if that don't work, you may want see what it says in the owners manual. Or you may have to take it to a shop. If the "Check Engine" light is coming on then there is a problem with the vehicle and there should be a "code" in the computer. Most auto parts stores will put a scanner on your car and read the codes for free. Those lights are there for a reason, if ignore them your car will let you down.

Jan 23, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Mitsubishi montero stalls, but is able to start


must have a bad o2 sensor need to check with a scanner auto zone and advance auto parts do it for free.

Jan 17, 2010 | 2001 Mitsubishi Montero

3 Answers

Yellow oil symbol kept turning on


this could be due to low oil. you need to check your oil level. if it is full i would do an oil change with a bmw filter. there is a difference in filters. the service engine soon light will have to be diagnosed. meaning pull codes to point you in the right direction. great car though. happy holidays

Dec 24, 2009 | 2000 BMW 3 Series

1 Answer

1995 Oldsmobile Cutlass Supreme low oil light keeps coming on.


OK WELL HERES HOW TO RESET UR OIL LIGHT TURN THE IGNITION ON-AND STEP ON THE GAS PEDAL 4 TIMES AND UR OIL LIGHT WILL BE RESET THIS USUALLY HAPPENS WHEN YOU DO A OIL CHANGE UR SELF THIS ARE TRICKS THAT THE GM HAVE HOPE THIS HELP

Feb 19, 2009 | Isuzu Trooper Cars & Trucks

1 Answer

2005 Pathfinder Heat Flow problem


have the thermostat and heater core checked also check you antifreeze level in the radiator if its not full it wont atsy warm

Jan 14, 2009 | 2005 Nissan Pathfinder

Not finding what you are looking for?
1989 Toyota Camry Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...