Question about Subaru Cars & Trucks

Open Question

Oil dilution reset subaru forester 2010 euro4

How to do the oil dilution reset on a forester subaru euro4 2010

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: 1998 subaru forester runs rough when it rains.

Check the cap and rotor for internal carbon tracking or, just change them. Also, take a look at the coil when its dark and rainy and see if there is any arcing where the coil wire goes into it.

Posted on Jun 19, 2009

Ad
  • 119 Answers

SOURCE: subaru forester heater

take back to the dealer,hopefully the will find that the blend door cable is off or not adjusted properly

Posted on Jul 14, 2009

  • 507 Answers

SOURCE: Subaru forester check engine light came on. Found

no not nornal,you need to get it plugged in to a diagnostic computer to see which sensor set it off it means you have something that needs to be looked at,low oil could be a coincidence

Posted on Oct 29, 2009

Rebgagnon
  • 382 Answers

SOURCE: How do you reset the computer on a 1998 subaru

I am thinking you mean the alarm system. If so, Just locate the box under dash by where your left knee sits. It is about 4" x4" x 1". It has a wire lead that has a small button on it. Just push and hold the button for about 15 secounds and it will reset itself. That should stop the marker lights from flashing. Good luck and hope this helps. Have a great day.

Posted on Jan 19, 2010

  • 10 Answers

SOURCE: 2000 subaru forester ignition coil wiring

Are there any other possible problems, or you are just not receiving spark at all now?

The coilpack could be dead and just need replaced. If you have a voltmeter or a test light, check the wiring on both sides of the coilpack harness to make sure it is receiving power.
I don't believe Subaru used ignitors past '99, but if they did, your should be located on the firewall behind the throttle body. Make sure it's plugged in and receiving power.

Coil packs do go bad from time to time. I had to replace mine in my
'98 Impreza a while back.

Goodluck!

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where can i get a workshop manual for my 2010 subaru forester


Most autoparts stores carry them or try filepeep.com or
manualslib.com

Mar 20, 2015 | 2010 Subaru Forester

1 Answer

I have a 2010 subaru forester that i cannot refuel when check engine light is on


Although I have never encountered this issue on my own 2010 Forester, I would say that this may be a fuel system problem with a sensor or component. The place to resolve this is at a Subaru service department.

Jul 16, 2014 | 2010 Subaru Forester

2 Answers

Radio and dash clock stopped working


cant fix till it happens agin as problem has gone prob loose conection

Aug 18, 2012 | 2010 Subaru Forester

2 Answers

Can't put gas into my 2010 subaru forester


Having same issue with my 2010 subaru - seems common although the dealer refuses to admit it. P0453 CEL code indicates a problem with the EVAP - this came on a few days before I was no longer able to refuel. THey say I need a new Fuel Tank Pressure sensor. Essentially the fuel tank valve is closed, when it should be open when the ignition is off. Wating 4 days for the part, hopefully thats what it is. WHat ended up fixing your problem Tom?

May 28, 2012 | 2010 Subaru Forester

1 Answer

Can't put gas into my 2010 subaru forester


if the gas gauge reads empty it might be not working properly, and the tank could actually be full. I've seen this time and time again at my station over the past twenty some years. The other posibility could be an obstruction in the filler neck it self. Kids do the darndest things to cars ? LOL. If thats the case then there is Two hose clamps that hold it in place, usually a screw driver or a small socket will work. But first stick a peice of hose in there and try blowing through the hose and listen if you hear bubbles then its full if you hear just air then its empty and blocked. Good luck :- )

May 28, 2012 | 2010 Subaru Forester

2 Answers

I changed the oil but the change oil light is not going off what button should i push and hold to reset i have a subaru 2002 forester


Hello there :
What you can do also is to take the vehical to autozone and have them hook up the handheld diagnostic center to the vehical and they can clear the light and the good thing about this is that it is free
Hope that this is very helpful for you
Best regards michael

Dec 20, 2009 | 2002 Subaru Forester

1 Answer

1998 subaru forester runs rough when it rains.


Check the cap and rotor for internal carbon tracking or, just change them. Also, take a look at the coil when its dark and rainy and see if there is any arcing where the coil wire goes into it.

Jun 19, 2009 | 1998 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...