Question about Seat Altea

Open Question

How to remove door panels om seat leon

How to remove drivers doo panel to change actuater

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 187 Answers

SOURCE: How do remove drivers side door panel

First you need to remove the door handle and window crank by pushing back the ring and releasing the handles. Also the arm rest will have screws into the steel door frame that must be removed. The panel itself has plastic snaps that are pushed into holes in the doors steel frame. The trick is to slide a pry bar or even two is better, one on ether side of the clip and force the pin out. You need to be patent and do one at a time. The door panels are made of a less than hard strong material and will brake apart easily especially if they are older. The clips go all the way around the lower three sides and the top will lift off the sill.

Posted on May 07, 2009

Ad
  • 1986 Answers

SOURCE: how to remove a 1999 civic se left door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: removing door panel drivers side to connect mirror wiring behind this panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: door panel removal for 2002 9-5 on driver rear

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

  • 1986 Answers

SOURCE: need directions to remove driver door interior panel 1997 deville

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

How do i replace the park assist module in a 2011 chevy traverse???/


Have you checked the fuse? If so, the module is located behind the left rear trim panel. Remove the panel to access. Below is a diagram of the trim panel and location of the module in BLUE>
Preliminary Procedures
  1. Move the rear seat to the full forward position.
  2. Remove the rear number?2 seat . Refer to 3rd Row Seat Removal and Installation.
  3. Remove the rear quarter upper trim panel. Refer to Quarter Upper Trim Panel Replacement.
  4. Disconnect the liftgate actuator rod from the liftgate. Refer to Liftgate Actuator Rod Replacement.
  5. Disconnect the rear seat number 2 shoulder belt anchor bolt. Refer to Rear Seat Number 2 Retractor Side Belt Replacement.
  6. Remove the liftgate door sill plate. Refer to Liftgate Door Sill Plate Replacement.



woauitf41mzpgaaaabjru5erkjggg==

Nov 16, 2014 | 2011 Chevrolet Traverse

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

How to replace the driver side blend door actuator in a 1999 cadillac deville


Air Mix Actuator Replacement - Driver





Removal Procedure





  1. Remove the right sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.


  2. Remove the instrument panel compartment. Refer to Instrument Panel Storage Compartment Replacement in Instrument Panel, Gauges and Console.


  3. Unsnap the rod from the plastic retainer on the actuator arm.

  4. Remove the two screws from the actuator (2).


  5. Disconnect the electrical connector (1).


  6. Remove the actuator (2).


  7. Inspect the air mix door for free travel.

Jul 06, 2012 | 1999 Cadillac DeVille

1 Answer

How to remove the in door of a 1990 bmw 325i? And also the drivers door will not lock when i turn the key the other doors lock but the drivers door doesnt how should i go about fixing that?


Sounds like you need to replace the power door lock actuator for the driver's door.


E30 Models
  1. Remove the door panel and the water shield.
  2. Disconnect the wiring from the actuator. Remove the screws and pull the actuator off the linkage.
  3. When installing, move the actuator and linkage to the locked position.
  4. Connect the linkage to the actuator and loosely install with the screws.
  5. Compress the actuator drive to take out any play in the linkage and tighten the screws.
  6. Test the locks and install the door panel.

E36 Models
  1. Remove the door panel and water shield.
  2. On the front doors, remove the guide rail nut and pull the guide rail down. Disconnect the wiring and the linkage from the actuator.
  3. On the rear doors, remove the window and the access panel. Disconnect the wiring and the linkage from the actuator.
  4. Remove the 3 bolts holding the latch and actuator to the door structure.
  5. Install in reverse order using threadlocker on the bolts.

Mar 16, 2011 | 2003 BMW 325

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

97 maxima SE driver door wont open from inside or outside dealer said it was door actuator and lock assembly. the door is in the closed position. I need advice the dealer wants 750$. Is there a cheaper...


The doorlock-actuator can be accessed with the inner door panel removed. It is difficult to get to with the seat in the way, but backing the seat all the way to the rear will help.Once you get the panel off, the actuator can be removed. I would check the electrical connection to that solinoid before I removed it, as it may be a simle as that in that model.

Mar 21, 2010 | 1997 Nissan Maxima

1 Answer

I have a 1999 Honda Odyssey. The remote will not open or lock doo


YES I HAD THE SAME PROBLEM I FIXED IT BY REMOVING DRIVERS DOOR PANEL AND FOUND ACTUATOR OUT OF LINE AND WIRE CONECTORS WERE BROKE I COULD NOT FIND REPLACEMENTS SO I USED WIRE ROPE GRIPS I ALSO FOUND LOOSE CONECTIONS IN WIRING I GOT CENTREL LOOKING WORKING AGAIN, HOPE THIS IS HELP.

Oct 22, 2009 | 1999 Honda Odyssey

1 Answer

2001 Pontiac Montana Rear heat blows only cold air???


The rear temp blend door is stuck in the cold position ,very common problem on vehicles with rear HVAC units . There is no valve , electric actuator !
Air Temperature Actuator
The air temperature actuator is a 3 wire bi-directional electric motor. Ignition 3 voltage, ground and control circuits enable the actuator to operate. The control circuit uses a 0-12 volt linear-ramped signal to command the actuator movement. The 0 and 12 volt control values represent the opposite limits of the actuator range of motion. The values in between 0-12 volts correspond to the positions between the limits.
When the HVAC control module sets a commanded, or targeted, value, the control signal is set to a value between 0-12 volts. The actuator shaft rotates until the commanded position is reached. The module will maintain the control value until a new commanded value is needed.

You would need to remove the
Quarter Lower Rear Trim Panel
Remove the rear seats. Refer to Rear Seat Replacement in Seats.
Remove the back body pillar trim. Refer to Upper Rear Trim Finish Panel Replacement .
Remove the body side upper trim panel. Refer to Third Pillar Trim Replacement .

Remove the cup holder from the rear quarter trim.
Remove the rear accessory panel from the left side quarter panel. Refer to Rear Accessory Panel Replacement .
Remove the retainer bolt from the seat belt retractor. Refer to Rear Seat Belt Retractor Replacement in Seat Belts.
Remove the upper cargo net retainers. Refer to Cargo Net Replacement in Body Rear End.
Remove the liftgate sill plate. Refer to Liftgate Door Sill Plate Replacement .
Using J 38778 remove the rear quarter trim panel retainers.
Remove the rear quarter trim panel from the vehicle.
Search from over 10 Million Auto Parts

Oct 14, 2017 | 2001 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Adam Truesdale

Level 2 Expert

344 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...