Question about 2006 Volkswagen Jetta

Open Question

How do i replace my purge valve senolid on a 2006 vw jetta

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: 2006 vw jetta tdi service engine light reset

With the key in the ignition (but not turned), press and hold the Odometer Reset Button on the right hand side of the panel. While still holding that button, turn the key (although not far enough to start the engine) and then press and hold the Minute button on the left side of the instrument pane(if pressing doesnt work try turning the knob clockwise until service light has gone off and skip the pressing)l. Release both buttons at the same time.

Posted on May 30, 2009

  • 257 Answers

SOURCE: how to replace air filter on 2006 VW Jetta 2.5L

Here's a step by step with photos...

http://forums.vwvortex.com/zerothread?&id=2489995&postid=27536262#27536262

Posted on Jul 16, 2009

  • 972 Answers

SOURCE: Have a 2006 VW Jetta 2.5. Engine emission warning

you need to pull the codes and go from there

Posted on Mar 20, 2010

  • 1 Answer

SOURCE: 2006 vw jetta No power on drivers door.

I have the same Problem. I Simply cut into the middle of the boot between the door and body The broken wire was right there, I pulled each end out and held the wire there with a pair needle nose pliers, stripped the end with a knife and attach a mulyi-strand jumper between both ends with electrial wire twists. Leave 2" approx. then slip the boot back over them. Use # 14 Wire. A Quick reasonable fix. If brakes again repeat again. The new Haness will have the same Problem down the road.
John

Posted on Apr 07, 2010

Testimonial: "I had the problem fixed at the dealer. It was the harness They made the harness longer & it was free.. "

  • 257 Answers

SOURCE: VW 2006 Jetta TDI Code P2112

Anti shudder valve is the correct terminology. Check out this post (with pic) from tdiclub.com

http://forums.tdiclub.com/showthread.php?t=247671&highlight=p2112

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace alternator and battery 2 times in 6 months VW Jetta TDI


something is draining your battery, I would take it to an automotive electric mechanic .

Jun 29, 2013 | 2006 Volkswagen Jetta

2 Answers

My 2006 vw jetta needs transmission fluid. The manual says I have to take it into a vw dealership however, the closest one is two hours away. Can I add the fluid myself and how?


1. Check and add transmission fluid on a 2006 VW Jetta with manual gearbox:

tdisline_575.jpg
tdisline_579.jpg

2. Check and add transmission fluid on a 2006 VW Jetta with automatic gearbox:

tdisline_580.jpg
tdisline_581.jpg

May 26, 2011 | 2006 Volkswagen Jetta

1 Answer

What is po411 and po445 for 2006 vw jetta/


P0411- Means Secondary Air Injection System Incorrect Flow Detected!
Possible causes - Vacuum hoses damaged.
- Air Pump inoperative.
- Air bypass solenoid circuit open.
- Air bypass solenoid leaking/blocked or stuck open/closed.
- Air diverter valve leaking/blocked or stuck open/closed.
- Air air hoses r Possible solution - Visually inspect vacuum lines for disconnects in the AIR systems and visually inspect for proper vacuum line routing. Repair if necessary.
- Disconnect the air pump hose at the solenoid valve, start the engine and see if there is air being pumped P0445- Means Evaporative Emission Control System Purge Control Valve Circuit Shorted! Possible causes - Damage harness or connectors to the Purge Control Valve
- The valve circuit is open or shorted
- EVAP canister purge volume control solenoid valve may be faulty
P0445 Description The EVAP canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve. When is the code detected? - An excessively high voltage signal is sent to ECM through the valve

Jan 11, 2011 | 2006 Volkswagen Jetta

1 Answer

Trouble code PO440


First check for leak on a evaporator system hoses.If there is no any leaks-change evaporative canister purge valve

Jun 09, 2010 | 1996 Volkswagen Jetta

1 Answer

How do i fix a po440 code on a 1999 vw jetta 2.0


Check intake manifold and intake pipes for leaks. Check operation of Canister purge valve. [can cause pressure build up in fuel tank causing vehicle to cut out after driving a while.

Jun 09, 2010 | 1996 Volkswagen Jetta

1 Answer

How do i fix my purge valve on my o4 jetta


EVAP/evaporator purge valve can,t be clean-change it

May 06, 2010 | 2004 Volkswagen Jetta

1 Answer

VW 2006 Jetta TDI Code P2112 how do I fix the problem - I have heard throttle flap and I have heard ECR valve. How do I fix the problem?


Anti shudder valve is the correct terminology. Check out this post (with pic) from tdiclub.com

http://forums.tdiclub.com/showthread.php?t=247671&highlight=p2112

Apr 13, 2010 | 2006 Volkswagen Jetta

2 Answers

How to replace air filter on 2006 VW Jetta 2.5L


Here's a step by step with photos...

http://forums.vwvortex.com/zerothread?&id=2489995&postid=27536262#27536262

Jul 16, 2009 | 2006 Volkswagen Jetta

2 Answers

Jetta 2006 Code P0456


P0456: Evaporative Emission System Leak Detected (small leak)

Using a Multimeter, check the Evaporative Emission (EVAP) Canister Purge Regulator Valve N80 terminals 1 and 2 for resistance. You should get 22.0 to 30.0 Ohms. If not, replace the canister. If you do, you have other problems.

Apr 01, 2009 | 2006 Volkswagen Jetta

Not finding what you are looking for?
2006 Volkswagen Jetta Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...