Question about 1989 Peugeot 405

1 Answer

My pug 106 kreg brake lights dont work wen i press the brake my battary light coms on.my mate tryed to bridge 2 wires together witch connect to the brake switch and lights did not come on...

Posted by on

  • wayneinitm8 Mar 11, 2009

    have checked all fuses.have just been told its prob a bad earth from brake lights to the switch. o and the windo wipers or sterio dont work

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

Check the fuse, that is if you haven't already done so.

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 lincoln navigator brake lights do not work, but turn signals and lights work


Brake lamp switch may be faulty bridge the two wire together and see if brake lights come on if so get a new switch.

Jun 02, 2014 | 2004 Lincoln Navigator

1 Answer

2007 brake lights switch not working


Normally, the switch is right over your break pedal. it is a small piece with 2 wires. Disconnect the wire form the switch and try to bridge the contacts f.e. witch an paper clamp. If the break lights goes on, check if the switch is right placed. That means that the break pedal must hit the downside of the switch to press in a small plastic part that opens the contacts inside the switch. Try to move this part in with your fingers and check if it comes out quick if you press down the break pedal. If bridging works, but the reest not, replaces the switch and take care for proper installation

Apr 01, 2014 | 2007 Jeep Liberty Sport

1 Answer

Tahoe brake light switch


check bulbs first ,then unplug brake switch ,if the swith plug has 2 wiring running into it, use a thin wire to bridge the 2 wires of the plug and see if brake lights illuminate ,if they do work by bridging the wires with ignititon on , it is more than likely the switch at fault

Jan 15, 2014 | Cars & Trucks

1 Answer

Yukon brake light


You have power at the fuse. The brake light switch has two wires on it, one is the supply from the fuse the other is to the lights, Check for volts at the switch (yes), bridge the two wires then follow the wiring checking for a live. Start at a light and work your way back up the loom checking all connecting sockets, has the vehicle a trailer socket, check the multi-plug where it picks up the wiring.

Jan 03, 2014 | Cars & Trucks

1 Answer

How do i remove the sensor for the rear tailgate?


1) Locate and remove sensor.
The sensor is located under the drivers tail light. Unclip it from the body and then unplug it.

2) Bypass the tail light circuit.
Connect the tail light signal wire (Green) to the tail light wire (Green w/ Red Stripe). I recommend using wire tap in squeeze connectors that way you dont have to cut any wires.

3) Bypass the brake light circuit.
Connect the brakelight signal wire (Green w/ White Stripe) to the brake light wire (Red w/ Blue stripe) and the the 3rd brake light wire (Red w/ White Stripe). Again all three of these wires are to be connected together.

4) Throw away your broken Tail Lamp Failure Sensor
Do not plug your sensor back in. Doing so will cause the annoying orange lamp failure warning light on your dash to stay on. Leave it unplugged ant the light will stay off.

5) Test your work
Turn on your lights and make sure your tail lights work properly. Have a friend step on the brake pedal, and make sure your brake lights work properly as well. Dont forget to check the Third brake light.

Sep 20, 2012 | 2002 Chrysler Voyager

1 Answer

My brake lights are not working, My light turn on, my blinkers work, emergency lights flash, but nothing happens when I press on my brakes?


Sounds like a brake pedal switch fault take the switch of the brake pedal and remove connection , bridge the two wires and check if the b lights are working if so change the switch. If not check the bulbs

Oct 04, 2010 | 1995 Honda Accord

1 Answer

The brake light doesn't come on. the taillight brake lights do not come on. I replaced the bulbs. My rear lights come on, just not the brake lights.


the fuse is at fault. if all good on the fuse, bridge the 2 wires at the brake pedal switch together and see if they come on, if they do, refresh the switch.

Jun 13, 2010 | 2000 GMC Jimmy

2 Answers

My peugeot 206 all 3 of my back brake lights are not working


hi the first thing you need to check is the fuse in the fuse box if this is ok then the chances are the brake light switch needs replacing or it may have come loos what you need to do is get down on your knees so you can get a close look at the brake pedal then if you follow the brake pedal all the way to the top just before it goes through the bulk head into the engine you will then see a switch attatched to the very top of the brake pedal it will have 2 or 3 wires coming from it so check if this is fitted correctly also you could remove it and press the switch by hand and then see if the brake lights work that way.

If they do then try fitting it again and you may be able to adjust it slightly so check this if on the other hand it still dont work then you need to get it replaced.

Let me know how you get on or if you need further assistance ok

Jan 15, 2010 | 2006 Peugeot 604

2 Answers

Third brake light flashing when engine is off, no main brake lights


this does not sound like a fuse problem. seems like a wiring issue. You probably have wires shorted together, and/or shorts to ground somewhere.

Brake switch is a good place to start, make sure it's working fine. To find the wiring issue you will need electrical diagrams, so get yourself a repair manual for a 1998 Explorer.

Look at connectors, see if you can find components or connections where all the brake light and tail lights connect to together. Using a multi meter you should be able to pin point the issue if u follow the wiring from the battery to the lights using the diagrams and checking connectors.

May 09, 2009 | 1999 Ford Explorer

3 Answers

Brake lights on peugout 106


check the plug-in on the brake switch. also that switch is adjustable, maybe you can adjust it.

Jun 21, 2008 | 2005 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...