Question about Cars & Trucks

Open Question

How to replace a hose radiator on mercury villager 2002

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: Mercury Villager headlight assembly diagaram for removal

This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.

Posted on Dec 12, 2008

Ad
  • 341 Answers

SOURCE: Replace the thermostat on 2002 GMC Envoy

4.2L Engine the thermostat and the neck where the hose goes on is one unit $25 at autozone

  1. Remove the necessary coolant from the radiator.
  2. Remove the alternator, Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
  3. Remove the thermostat housing bolts.
  4. Remove the thermostat housing from the engine block.
  5. Clean all of the surfaces of the thermostat housing.
  6. Clean the sealing surface of the engine block.

Posted on Dec 29, 2008

emissionwiz
  • 76164 Answers

SOURCE: cant release spare tire from under car

Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
locations:
Item Location
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.

Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage
the retainer

Posted on Jul 12, 2009

  • 40 Answers

SOURCE: 2002 Chevy Cavalier how 2 replace radiator hose and a belt

First thing I would do is get your supplies. Antifreeze, lower radiator hose, 2 new hose clamps, serpintine belt, and I would purchase a Chiltons repair manual for your car. It is abour $15 for the manual but it will cover about very repair you will need to make as time goes on.
On newer cars you have to hold the automatic tensioner back with a wrench as you uninstall or reinstall the belt. Make sure you know or remember how the belt runs. You can put the belt most of the way on, then hold back the tensioner for the last step.
For the lower radiator hose, you need to drain the antifreeze from the radiator. The drain plug is usually on the bottom or the on the bottom engine side of the radiator. Make sure you drain it in a pan/ bucket/ pail as I believe it is against the law to drain it out on the ground and watch that pets/humans don't drink it because they will die. After draining it unsrew the clamps holding the hose on and remove the hose. Sometimes the hose will be stuck and twisting it or running a screw driver between the hose and the fitting will loosen the hose. Put the new hose on with the new clamps. I always use new clamp so you don't have to trust the old beat up/ stretched clamps. But don't throw out the old ones, as you may need them for an emergency repair sometime. Either put the old fluid back in(if it is still good) or put in the new stuff. Make sure you get the right mixture. You will need to run it a while and have the mixture checked.
Like I said about the book----it should cover both of these repairs, and tell you when to do routine maintence, the capacities of your fuel tank, radiator, oil, transmission, etc.

I hope this helps

Posted on Aug 10, 2009

  • 7353 Answers

SOURCE: 2002 dodge 1500 Changed radiator, thermostat, and hoses. No heat

Why was radiator replaced?Did it have heat before ? If it was plugged, the heater core may also be plugged. Try flushing it with a water hose in both directions. I dont know why the botton radiator hose would be cold, the radiator should be a uniform temp and the air coming through the radiator should be HOT, when the engine is at operating temp. What condition was the old coolant? if it was rusty, the water pump may have lower flow than normal.

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Mercury Villager keeps overheating. What else can it be or be done?


Exhaust Converter Blocked ?

Did you check for combustion gases at the
coolant or radiator fill

Your down to a head gasket or a crack somewhere

I would think the head gasket is common on that
motor possibly,research that

Timing Belt worn or jumped ?

Nov 18, 2014 | 2002 Mercury Villager

1 Answer

How to remove an alternator for a 1999 mercury villager


remove the belt.then remove the bracket for the belt tension. then remove the bottom alternator bolt. pull alternator up to top of radiator.may need to remove upper radiator hose and cooling fan assembly to get enough room to get the alternator out.

Jun 09, 2012 | 1999 Mercury Villager

1 Answer

I got a 2000 mercury villager top radiator hose is hot bottom one is cold why


dfepending on how longh you let it run. the flow may be restricted or stopped-up altogether. what about the heater hose and coolant level

Jan 16, 2011 | 1999 Mercury Villager

2 Answers

I have a 2001 mercury villager that overheats. I replaced the fan assembly and the thermostat. The radiator is fine. What else could be causing the van to overheat?


You have air trapped in the system. If you have cold air, warm air, cold air from your heater, then it's air entrapment. Very common these days. Go to a shop that uses vacuum method to refill cooling system & that will purge air.
Otherwise, you can try. Park uphill. cold engine - fill radiator to top with 50/50 mix of antifreeze. leave cap on but loose. fill reservior to 3/4 full. Turn heater to hot to allow coolant to flow through heater core. start engine, run at 1500 rpms until thermostat opens and upper hose is hot. tighten cap and let it cool down. after cool check level of reservoir. fill to top line on reservoir. it should **** coolant back into radiator as it cools down.
repeat if still an issue.

go to yahoo group for villager quest & join owner group for much more help. 2500 members.

Dec 07, 2009 | 2002 Mercury Villager

1 Answer

2002 Mercury Villager with weird brake problem


check the brake booster and vac supply to it. big hose on the booster.

Jun 05, 2009 | 2002 Mercury Villager

1 Answer

Overheating


you have air trapped in the system. very hard to "BURP AIR"

park uphill on ramps if possible. With cold engine, leave radiator cap loose and fill radiator and reservoir. run engine until thermostat opens. squeeze upper radiator hose with hand. SHould be hot. Have heater on hot and blower on too. Repeat as necessary. May take several attempts.

Go here and we can help if that does not work

http://autos.groups.yahoo.com/group/villagerquest/

May 02, 2009 | 2002 Mercury Villager

2 Answers

No heat


if you replaced the thermostat, you have an air bubble trapped in the engine. So, you don't have any coolant running through the heater core, therefore no heat.
sometimes hard to "burp" air bubble. Try this. Park park facing uphill and jack up front of car too. You want to get radiator opening higher than top of engine. Then remvoe radiator cap (cold engine), fill radiator, then fill coolant reservoir to full point. Install radiator cap but leave it loose so air can escape. Start engine until upper radiator hose going into radiator is hot. This should burp air. Repeat a few times while adding coolant mix (50/50 antifreeze) to keep radiator full. Be careful not to remove radiator cap when engine is hot.
lwt us know how ou make out. There is a more complicated procedure but you need tools and knowledge of where air bleed is on top of engine

Jan 03, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...