Question about Cars & Trucks

Open Question

REAR HUB TORQUE SETTING CITROEN RELAY VAN - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 61 Answers

SOURCE: Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.

Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Posted on Jul 24, 2009

Ad
  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

  • 144 Answers

SOURCE: rear hub nut torque settings for a suburu impreza

122-152 FOOT POUNDS(THE AXLE NUT MAINTAINS THE PROPER PRESSURE ON THE HUB TO ENSURE THE HUB STAYS IN PLACE)

Posted on Aug 31, 2009

citroenchris
  • 600 Answers

SOURCE: Citroen Relay HDI Van. Have no dip headlights.

Probably not, the fog lamp relay works off the dip beam power, is there a relay for the dip beams?

Posted on Jan 02, 2010

pugwash814
  • 377 Answers

SOURCE: Does anyone know the torque wrench settings for

Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

3 Answers

KEYCODE light permanently lit on Citroen Relay van,


before u buy have trouble code scanned most auto stores offer service for free ==can be as simple as a bad key[not recognized] to big such as electrical anti -theft system

Apr 26, 2010 | 2006 Fiat 124

1 Answer

Torque setings


if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Jun 02, 2009 | 2003 Renault Sportwagon

1 Answer

Renault laguna 2 rear hub turqe settings reg 51


hi -
THE REAR HUB TORQUE SETTING IS 280 NM OR 207 IBF FT. HOPE THIS HELPS
good luck kas

Sep 23, 2008 | 2001 Renault Sportwagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...