Question about Opel Cars & Trucks

Open Question

Headlight adjustment for opel corsa

Headlamp adjustment

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: 1998 headlight adjustment

the intrigue is verry simple.there are plastic knobs under the hood,just above the headlamp,on either side,respectively.

Posted on Dec 15, 2008

Ad
pugwash814
  • 377 Answers

SOURCE: opel astra headlight adjustment

two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks

Posted on Nov 07, 2009

  • 6982 Answers

SOURCE: 2001 opel corsa 1.4 is utility. Snapped the

Likely you are talking about the harmonic balancer.
The bolt turns counter clockwise and is generally removed using an air gun. There is another way to do that too but it is a bit dangerous. Using a solid breaker bar (one without jointed end) you can brace the end against the ground with the socket installed on the crank bolt (I actually have a pipe driven into the ground outside just for doing this...I just slide the bar into the pipe and keep it form dropping by using a vise grip on the handle). Once the socket is on the bolt, crank the engine over using the starter, the engine will force the bolt to back out.
After you get the belt installed, tighten it as much as you can by hand and ask a shop to just give it a final tightening with an air gun.
If the socket slips the bar can fly up so be very careful and don't stand where it can hit you!

Posted on Feb 15, 2010

max_output
  • 28 Answers

SOURCE: Reverse lights on Opel Corsa Classic 2000 model not working

check to see that when you put the car into reverse that it is hitting the switch and pressing it in properly, you may need to adjust the switch for it to make proper contact

Posted on Nov 20, 2011

alicantecoli
  • 22326 Answers

SOURCE: My Opel Corsa dies down during driving, it will only start again after 7 to 10 mins, l have no clue whats happening.

No idea offhand to be honest i would need my head under the bonnet to know what wrong .could be anything from the gauze filter in the fuel tank on the bottom of the fuel pump becoming chocked up and leaving the car allows it to drop away to a faulty pump overheating or the contacts ,maybe even a ignition module overheating ,Best advice is ask a local mechanic to have a look for you as normally these early opel corsas with the 4 cylinder engine are bullet proof they are even valve free if the timing belt snaps .

Posted on Jan 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlight adjustment on 2005 Chevy cavalier


Get flat screwdriver and star screwdriver

menu

How to Adjust a Headlamp Beam on a 2005 Chevrolet Cavalier...

When you replace the headlamp assembly in the 2005 Chevrolet Cavalier, you must also adjust the headlamp beams. Like most vehicles, there are two screws located on the headlamp assembly that control the vertical and horizontal direction of the headlamps. Proper adjustment is necessary for adequate visibility during nighttime driving; bad adjustment can make it difficult for you to see or make it difficult for oncoming drivers to see, creating a potentially dangerous situation. You can adjust the headlamp beams yourself with a screwdriver in about 15 minutes.
Park the Chevrolet Cavalier on a flat surface facing a wall or garage door approximately 15 feet away. Park the Car so that it is perpendicular to the wall.

Lift the hood and remove the plastic trim panel above each of the headlights. There are three plastic fasteners that secure the trim panel; pry the fasteners out using a flathead screwdriver. Lift the trim panel up to remove. There are two adjusting screws beneath the trim panel, one on the top of the headlamp assembly and one along the outer side of the headlamp assembly.

Turn the headlights on so that they shine on the wall. Ensure the headlights are on the "dim" setting.

Adjust the vertical bolt, located on the top of the headlight assembly near the center of the vehicle to raise or lower the headlight, using a crosspoint screwdriver. Turn the screw counterclockwise to lower the headlamp beam; turn the screw clockwise to raise the headlamp beam. Adjust the headlamp so that the beam is below a driver's eye level.

Adjust the horizontal bolt, located on the outer side of the headlamp assembly to move the headlamp beam right of left, using a crosspoint screwdriver. Turn the screw counterclockwise to move the headlamp beam right; turn the screw clockwise to turn the beam left. Adjust the headlamp so that the beam shines straight ahead or slightly toward the center of the vehicle.

Replace the plastic trim panel and fasteners and close the hood. Warning: raising the lights too high can make it difficult for other drivers to see you.

Dec 11, 2017 | Cars & Trucks

1 Answer

Remove and replace headlights 2001 f350


is it a plastic lens AERO haedalmp or rectangular glass?

SECTION 417-01: Exterior Lighting 2001 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly -Headlamp, Aerodynamic Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp assembly.
    1. Pull up and remove the two upper headlamp clips.
    1. Release the lower headlamp clip.
    1. Position the headlamp so the electrical connector can be accessed.
    1. Disconnect the headlamp electrical connector.
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

snorkelbobby_77.gif

Jul 24, 2011 | Ford F-350 Cars & Trucks

1 Answer

Changing headlamp, how to..diagram


SECTION 417-01: Exterior Lighting 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Lamp Assembly-Headlamp (Explorer) Removal
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the parking lamp assembly. Refer to Lamp Assembly-Parking (Explorer) or Lamp Assembly-Parking (Mountaineer).
  1. Remove the headlamp assembly.
    1. Compress the self-locking tabs.
    1. Remove the headlamp assembly.
    1. Disconnect the electrical connector.
Installation
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n75014&c35=wsm%2clamp%20assembly%u2014headlamp%20%28explorer%29%2csxn%2c417-01%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_29.gif

Dec 29, 2010 | 1999 Ford Explorer

1 Answer

I need to find the fuse location for the headlamps on a 1999 Audi 2.8 A4 Quattro? Can you help?


The fuses location for the headlamps on a 1999 Audi 2.8 A4 Quattro are:
F18 (10 A) - RH headlamp - high beam
F19 (10 A) - LH headlamp - high beam
F20 (10 A \ 15A) - RH headlamp - low beam, headlamp adjustment
F21 (10 A \ 15A) - LH headlamp - low beam, headlamp adjustment

For Audi A4 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.

Sep 20, 2010 | 1999 Audi A4

1 Answer

I have a ford f350 and am trying to remove the old headlight assembly and replace with new one, can't seem to find out how to detach it from the truck


this for aero headlamp, plastic lens. please rate.

SECTION 417-01: Exterior Lighting 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly —Headlamp, Aerodynamic Removal
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp assembly.
    1. Pull up and remove the two upper headlamp clips.
    1. Release the lower headlamp clip.
    1. Position the headlamp so the connector can be accessed.
    1. Disconnect the headlamp connector.
Installation
  1. Install the headlamp assembly.
    1. Position the headlamp assembly.
    1. Connect the headlamp connector.
    1. Install the lower headlamp clip.
    1. Install the two upper headlamp clips.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment—Photometric Aiming or Headlamp Adjustment—Screen Method Aiming in this section.
      • d1d723b.gif

Aug 09, 2010 | 1999 Ford F350 Regular Cab

1 Answer

Headlight lens removal


1997 F-250/350/Super Duty Headlamp Assembly Removal
  1. Remove two screws and two nuts retaining headlamp door (13064).
  1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
  1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
  1. Remove two retainers attaching upper two attachments of headlamp (13008).
  1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
  1. Pull headlamp from vehicle

Jul 18, 2009 | 1995 Ford F250

1 Answer

Adjust headlamps 99 contur


Headlamp Adjustment Alignment
  1. NOTE: All adjustments should be made with headlamps off and at room temperature.
    Prepare the vehicle for headlamp adjustment.
    • Place the vehicle on a level surface.
    • Before aligning the headlamps, check them for faulty lenses, reflectors and blackened bulbs, and install new components as necessary.
    • Check the tire pressures and correct as necessary. For additional information, refer to Section 204-04 .
    • The vehicle must be unloaded with the exception of a tool kit and spare tire. The fuel tank should be half full.
    • Bounce the vehicle several times both front and rear or roll it a few meters so that the suspension settles.
  1. Locate the headlight adjustment screws.
    1. Vertical adjustment screw.
    1. Horizontal adjustment screw.
    2. fff6f56.gif
  1. Adjust the horizontal headlamp screw until the Horizontal indicator aligns with the "0" reference mark.
    1. Horizontal adjustment screw.
    1. "0" reference mark.
    2. 44b5acc.gif
  1. Adjust the vertical headlamp screw until the bubble is centered.
    1. Vertical adjustment screw.
    1. Bubble level indicator.
    2. fa71983.gif

Jul 04, 2009 | 2000 Ford Contour

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    Install headlight


    Headlamp Assembly Removal
    1. Remove radiator air deflector from radiator support.
    1. Remove two screws and two nuts retaining headlamp door (13064).
    1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
    1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
    1. Remove two retainers attaching upper two attachments of headlamp (13008).
    1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
    1. Pull headlamp from vehicle.

    Feb 26, 2009 | 1995 Ford F150 Styleside Regular Cab

    1 Answer

    Instructions on replacing headlight assembly


    96 f150 procedure

    Headlamp Assembly Removal
    1. Remove radiator air deflector from radiator support.
    1. Remove two screws and two nuts retaining headlamp door (13064).
    1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
    1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
    1. Remove two retainers attaching upper two attachments of headlamp (13008).
    1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
    1. Pull headlamp from vehicle.

    Oct 17, 2008 | 1994 Ford F150 Styleside Supercab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    843 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Opel Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Brad Brown

    Level 3 Expert

    17102 Answers

    The Scrivener

    Level 2 Expert

    154 Answers

    Are you an Opel Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...