Question about 1996 Jeep Grand Cherokee

1 Answer

Iddler pulley air conditioning bracket is broke

Posted by on

  • Greg Bernett
    Greg Bernett May 11, 2010

    So are you asking how to replace?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Expedition 2001 crankshaft sensor location and installation


  • Located front of engine, close to crank pulley
  • press the helpful button and follow me on Fixya for more tips
  • Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.
  • Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioning compressor's pulley.
  • Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.
  • Pull the electrical connection off the crankshaft sensor.
  • Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.
  • Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.
  • Press the electrical connection onto the crankshaft sensor.
  • Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.
  • Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley. write up found @ehow

How to Replace the Crankshaft Sensor in Ford 150 eHow

Jan 28, 2016 | Ford Expedition Cars & Trucks

1 Answer

How to bypass the air condtioning


Not really. I am not aware of that model being sold without ac.
So there would not be a belt and idler pulley used in place of the compressor.
The easiest way to fix it is to get a used compressor and put it on. You don't have to charge the ac for the pulley to work.

Apr 04, 2013 | 2001 Ford Taurus

1 Answer

Accent broking timing belt now misfire 1&4


Lift the vehicle by using of jack.
Remove the engine support bracket.
Remove the power steering belt.Remove the air conditioning compressor belt.Remove the alternator belt
Remove the coolant pump pulley.
Remove the crankshaft pulley.
Remove the timing belt cover.
Move the timing belt tensioner pulley toward the coolant pump and temporarily secure it
.Remove the timing belt
Remove the camshaft from the camshaft sprocket
Remove the crankshaft sprocket and flange.
Remove the timing belt idler.
Remove the timing belt tensioner.

re install in reverse order. chances are the rod is bent but without breaking down the cylinder the only way to determine is to but a new belt on and see what happens. good luck.

Mar 11, 2013 | 2001 Hyundai Accent

1 Answer

Position of cam shaft censor in the ford f150


nstructions
    • 1

      Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.

    • 2

      Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioningicon1.png compressor's pulley.

    • 3

      Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.

    • 4

      Pull the electrical connection off the crankshaft sensor.

    • 5

      Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.

    • 6

      Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.

    • 7

      Press the electrical connection onto the crankshaft sensor.

    • 8

      Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.

    • 9

      Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley.



Read more: How to Replace the Crankshaft Sensor in a Ford F-150 ' eHow.com http://www.ehow.com/how_6769823_replace-crankshaft-sensor-ford-f_150.html#ixzz2Ebai9Ftj

Dec 09, 2012 | 1998 Ford F150 Regular Cab

1 Answer

How to put a air condition belt a 1997 geo metro


there should be an adjustment bolt somewhere on the bracket. turn it one way it pulls the AC pulley towards the other pulley put the belt on then turn the adjustment bolt the opposite way and it will push it away and tighten the belt. you only want about an 1/8 inch play in the belt so the tighter the better

Jul 16, 2012 | 1997 Geo Metro

1 Answer

Timing chain is loose how do I replace or tighten


You need to pull out the timing cover. 4-6 hours of work. Here is the step to remove the Cover, then you need to remove the Sprockets.
moz-screenshot.pngmoz-screenshot-1.png
  1. Remove the oil pan.
  2. Remove the power steering belt if so equipped.
  3. Remove the air conditioning belt, compressor and bracket if so equipped.
  4. Remove the fan clutch (fluid coupling), with the fan and water pump pulley.
  5. Matchmark and remove the crankshaft pulley(s). This bolt will be very tight. Use the counter-holding bar, properly installed, to hold the crankshaft while loosening the bolt. Use the pulley extractor or gear puller to remove the pulley from the shaft.
  6. Remove the water bypass pipe.
  7. Remove the fan belt adjusting bar. If necessary, remove the lower power steering bracket for access.
  8. Disconnect the heater water outlet pipe.
  9. Unbolt the timing chain cover assembly. Be careful to loosen only the correct bolts.

To install:
  1. Install new gaskets over the dowels on the timing chain cover. Slide the cover assembly over the dowels and pump spline. Insert the retaining bolts and tighten them. Tighten the 8mm bolts to 9 ft. lbs. (13 Nm) and the 10mm bolts to 29 ft. lbs. (39 Nm).
  2. Temporarily install the adjusting bar to the alternator. Install the adjusting bar to the chain cover and tighten the bolts to 9 ft. lbs. (13 Nm).
  3. Install the heater water outlet pipe.
  4. Install the water bypass pipe.
  5. Install the crankshaft pulley and bolt. Use the counter-holding tool to hold the pulley and tighten the bolt to 116 ft. lbs. (157 Nm). If equipped with air conditioning, install the second crankshaft pulley.
  6. Install the water pump pulley and fluid coupling with the fan.
  7. Adjust the tension on the drive belts.
  8. Install the air conditioning compressor bracket, compressor and belt if they were removed.
  9. Install the power steering belt and adjust it.
  10. Attach the oil pan.
  11. Install the radiator.

Jun 04, 2010 | 1987 Toyota Pickup

1 Answer

How do u instal a fake pulley on air condition unit on 1997 pontiac grand prix


You need to remove the compressor and then align the pulley bracket holes with mount points on the engine. Check alignment by sighting from the side. The pulley should not be further out or in than the other pulleys on the engine. Use flat washers between the mount and the engine to correct any mis-alignment.

Mar 09, 2010 | 1997 Pontiac Grand Prix

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

Engine run rough at idler and surges


I would change the fuel filter and see if that don't help. You might give it a good tune up and adjust the timing. ( If it has a carburetor then adjust the carb too.

Apr 08, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Needing to remove ac compressor to install ac bypass pulley


There are a couple of ways to approach this. I just did one of these for a friend. The A/C pump seized while running. The serpentine belt broke. Crazy things can happen to other components when this occurs. In this case the broken ends of the belt, I think, whipped back around on itself on the crankshaft pulley and one of the other pulleys in the belt circuit and devastation occurred. 1) It snapped the power steering pump bracket in two. 2) It took out the alternator. 3) And not to be left out, GOODBYE cool blowin air conditioning. Time to decide what to do. He had to order the power steering bracket from a dealer (junk yards were cleaned out). He decided to replace the power steering pump with a remanufactured unit and new hoses (parts houses are much cheaper than dealer parts folks). You'll need a pulley remover that you can usually borrow (with a deposit) from some parts houses. He HAD to buy the alternato ya gotta have juice. I have been using the name, "parts houses" . (Can we use specific company names in this forum MR./MS. Editors ? I Feel I need to for the sake of all of us that come here for correct information.) THE ANSWER : DO you want to drop the bucks into fixing your A/C ? NO ? It can be involved and costly depending on how good of a do it yourselfer you are. New pumps are spendy. Then, if you use the older refridgerant you'll need a conversion kit and blah blah blah. YOU have opted for a bypass pulley. COOL ! Errrr...not actually. It's coming out. The bolts that hold the A/C pump to its bracket come out from BEHIND the bottom of the unit. They are long and won't clear the intake manifold,at least not easily. Take the bracket bolts out from the front. Take the hose from the pump to the dryer apart (at the dryer). Do you want to preserve the system for future repair? If so, cover that connection on the dryer to protect it from the world. With a sharp blade, cut the other hose coming off the pump right behind the grill. Or, try to take the fitting apart at the evaporator. Cutting it is easier. Plug the cut off end if ya want. Future repair thing. Rotate the pump forward so you can either take the bolts out,or remove the pump and bracket as a unit, with the lengths of hose attatched to the pump. This gets all that hose you no longer need out of the engine compartment. NOW THE BYPASS PULLEY. He found a pulley from NAPA. IT DOES NOT WORK ! YOU DO NOT NEED IT ! Nothing against NAPA. I have bought good parts from them before. Maybe their supplier does not know. The pulley is supposed to drop into the A/C bracket in the concave recess that the pump once occupied. IT WASN'T EVEN CLOSE. Chevy released THREE versions: Poor Boy-no power steering,no A/C. MIDMan-power steering,no A/C. Rich Guy-power steering,with A/C. SO....... If you have power steering, the A/C pump removal just put you into Midman status. Stop at your local chevy dealer, ask them to print you a belt routing diagram from the computer parts book. It shows all three versions. Go to your local,,,,,,,"PARTS HOUSE", tell them info...year,make,engine size, REMEMBER.. IT NO LONGER HAS AIR CONDITIONING. YOU'LL GET A SHORTER BELT !! IF, they sold you the bypass pulley.....GET YOUR MONEY BACK !!! Use the diagram you got. The belt is routed a little different since you lost the A/C pump and the idler pulley with it's bracket(that you can keep for future repair or trade in for to be made into beer cans) Also remember that without a belt on, the tensioner pulley is swung over to the end of it,s range of motion. When you get the belt routed correctly you have to put a wrench on the bolt on the pulley and turn hard to compress the spring. (COUNTERCLOCKWISE) The bolt is left hand thread so it won't come loose while ya reef on it to get the belt swung onto the ALTERNATOR LAST.<<<<<<GOOD LUCK !!! ADDED NOTE: Would that bypass pulley work on say...an "88" or "89" or "90" ? > I DO NOT KNOW. DID CHEVY change the size of the pump bracket after 87 ? We will be letting the good folks at NAPA know what we ran into and how we fixed it. We also will ask for a refund on the wrong part for the job. IT DOES NOT FIT AN 87! WE DO KNOW THIS..... IF the belt had just broke in half and safely dropped away, then all those parts wouldn't have been needed and the cost of the fix is FOR A SHORTER BELT and a little sweat to remove the A/C pump and bracket. The A/C NEVER WORKED ANYWAY

Jun 21, 2008 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...