Question about 1988 Toyota Pickup

1 Answer

Instrument panel not working, no tail lights, signals, brake lights

Think battery cables got crossed?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Check the fuse panel on passenger side front feder well under hood and fuse panel in cab on drivers side

Posted on May 10, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: Dashboard Lights

there is light bulbs behind the instument cluster. You will have to remove the screws, than pry off your panel and change the bulb.

Posted on Mar 31, 2009

honeymokey
  • 3113 Answers

SOURCE: brake lights suddenly do not

Brake light switch would be next.

Posted on May 10, 2009

Sgt Fluffy
  • 157 Answers

SOURCE: 1994 Camry - Brake Lights Work, Tail Lights Wont

Well Jennifer, it sounds like you've done all the things that I'd have done. Try for a bad ground next. Do the lights in the dash cluster work? They're wired together with the tail-lights (so that you know if the rears go out). There should be a ground wire somewhere connecting the body to the engine or chassis.Look around the rear of the engine bay. Good Luck.

Posted on Jun 10, 2009

  • 3600 Answers

SOURCE: tail lights and instrument panel lights out. all

how bout the brake lights if they are burnt out then the dash lights won't work thats to let yo know they are burned out.

Posted on Jun 25, 2009

flamierd
  • 1 Answer

SOURCE: Toyota Corolla 2006; Dash lights not working and

I had the same issues. Dash dead, tail lights dead. Fuses were fine, Dimmer relay was fine...So I got to the Tail Light Relay.

Removed the glove box, one screw on the right. Reach up (above the space where the glove box 'area' would be and there are 3 or 4 relays all sitting on top of a junction box. All of them were loose. I pushed them in...and voila! I was getting scared after the obvious.

Posted on Jul 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

2003 Pontiac Vibe no tail lights, brake lights and turn signals work just fine. The dimmer switch does not dim the dash lights but does work the dome just fineand the lights for the Heat/AC are off.


The tail lights work off the headlight switch, and there is a fuse for the tail lights. Make sure the fuse is good, first, a 15 amp (blue) fuse in the instrument panel fuse block. Then, you might have a bad headlight switch.
So you DO have dash lights, they just don't dim from the dimmer switch? In the wiring diagram, there is a green wire from a "tail light relay" (in the "Junction Block-Right Instrument Panel") that carries power to all the exterior lamps, as well as having a splice to the Instrument Panel Cluster (illum. bulbs), and to the lamp dimmer, and to the radio bulb.
To do any further testing, you would need a voltmeter or a test light, so you could chase down this power loss. Good luck.

Oct 17, 2016 | 2003 Pontiac Vibe

1 Answer

Brake lights work but tail lights don't work 91 LSC


check and make sure you have the correct light bulb in the tail lamp fixture.

Oct 15, 2013 | Lincoln Cars & Trucks

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

2 Answers

Interior dash and running lights dont work but my signal and brake lights work else works


Look at fuse #18, a 15 amp fuse, in the fuse block. This fuse powers both the tail lights and instrument cluster lights. Usually both of these light systems are powered by the same fuse so when your cluster isn't lit up you'll know right away that your tail lights aren't working as it's not safe to drive without tail lights. Your brake, turn, and head lamps are powered by different circuits. Hope this helps and good luck!

Aug 11, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

On 2002 jeep laredo brake lights dont turn on if lights arent on


That does not make any sense. Do the tail lights work? There are supposed to be separate filaments for brake lights, tail lights, and turn signals. In particular the center brake light should not be possible to be confused with tail lights or signals. Does it come on? If not, then you probably have no brake lights at all, and that is probably because of the bad fuse or the switch on the brake pedal for the brake lights.
If there is some sort of cross over between tail light and brake lights, that is usually from a bad light socket ground; which results in current backing up from one system to another. But then each is usually only half brightness.

Jul 20, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Instrument panel lights,and tail lights do not work


Chk. fuse, there both on same curcit.

Apr 04, 2009 | 2003 Acura RSX

1 Answer

Tail lights don't work on 1998 Chevy Silverado.


check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Feb 16, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Rear taillight problems


I had the same problem with my 1996 Mystique about a year ago. The brake and tail lights stopped working, except for the center brake light in the window. Turned out to be oxidation of the terminals at the connector on the turn signal. Yes, that's right, turn signal. The electrical signal to the tail lights goes thru the connector on the turn signal. To fix, I cleaned the contacts and the brake lights started working again. Hope this helps. Cheers, Henry

Nov 25, 2008 | 1998 Mercury Mystique

Not finding what you are looking for?
Cars & Trucks Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...