Question about Pontiac Cars & Trucks

1 Answer

I am trying to take the lower control arm on the passenger side of a 98 transport. The lower ball joint is being stubborn. I tried ball joint remover tool and not much room to work with and still dont

98 pontiac transport/montana

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Lower Control Arm

Print
The lower control arm is a two-piece welded unit with a riveted ball joint. A conventional rubber bushing is used for the rear lower control arm pivot. The front lower control arm bushing is mounted vertically.


REMOVAL AND INSTALLATION

Some special tools are required to perform this operation including, a front hub spindle removal tool and a suitable ball joint separator tool.

WARNING Do not hammer or pry ball joint from knuckle. Failure to use recommended tools may cause damage to the ball joint and seal.
See Figure 1


I am trying to take the lower control arm on the p - 0900c152801dbd3a.jpg enlI am trying to take the lower control arm on the p - enlarge_tooltip.gifs=enlarge_tooltip.gif

Fig. Fig. 1: Exploded view of the control arm-to-frame mounting

  1. Raise the vehicle and suitably support by the frame allowing the control arms to hang free.
  2. Remove the wheel and tire assembly.
  3. Remove the steering gear outer tie rod from the steering knuckle.
  4. Remove the stabilizer shaft link from the control arm.
  5. Remove the front drive axle shaft nut and washer.
  6. Use a suitable front hub spindle removal tool to Push the axle splines back out of the front wheel drive shaft bearing.
  7. Remove the drive axle from the transaxle.

Drive axle joint seal protectors should be used anytime service is performed on or near the drive axles. Failure to observe this could result in joint or seal failure.
  1. Place a modified inner drive joint seal protector on the drive axle joints.
  2. If equipped, remove the ABS wheel speed sensor jumper harness.
  3. Remove and discard the cotter pin, then loosen the nut from the ball stud.
  4. Remove the pinch bolt and the control arm mounting bolts, then remove the control arm from the vehicle.

Posted on Apr 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: front upper ball joint replacement

The dealer's answer (if you are interested).......

The ball joint is pressed into the upper control arm and has a tapered stud for attachment to the steering knuckle. The ball joint stud is attached and locked into the steering knuckle using a special nut. The ball joint is a sealed-for-life type and requires no maintenance. If the ball joint is defective it will require replacement of the entire upper control arm.

Sorry.

Posted on Jun 20, 2008

junkman1249
  • 552 Answers

SOURCE: Replacing Ball Joints on 2001 Mazda B2500 (upper and lower)

its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them

Posted on Mar 31, 2009

  • 316 Answers

SOURCE: Ball Joint connecting lower control arm and spindle 99 Grand Prix

Take a grinder or torch and cut the nut off.

Posted on May 13, 2009

  • 5 Answers

SOURCE: volvo s80 ball joint removal

Note that there is a Recall Campaign (99) on ball joint durability.  That is, your Volvo dealer will fix it free.

Posted on Jun 04, 2009

  • 72 Answers

SOURCE: Upper and lower ball joint replacement

to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much of a job is replacing control arm/ball joints on my 98 Windstar?


YOU HAVE TO REPLACE WHOLE LOWER CONTROL ARM IF LOWER BALL JOINTS IS DEFECTIVE BECAUSE LOWER BALL JOINT IS SEALED AND IS A INTEGRAL PART OF THE LOWER CONTROL ARM BOTH IS COMBINED A ONE UNIT.

Feb 21, 2011 | 1998 Ford Windstar

1 Answer

How do I change my lower contol arm, right side in my 2000 ford focus se?


remove the wheel. then take out the lower ball joint bolt.remove the tie rod from the assembly this makes it easy to swing the assembly back and forth. using a ball joint fork insert it between the the ball joint and lower control arm and wack the end on it till the ball joint separates from the control arm. using a pry bar put it thru the control arm so you can pry down on the control arm to release the ball joint then towards the back of the control arm are 2 nuts remove these and remove the cap that they hold towards the front of the control arm is one more nut remove this one and then pull out the control arm replace in reverse orderonetufshoppe_40.gifonetufshoppe_39.gif

Jan 24, 2011 | 2000 Ford Focus

2 Answers

Lower ball joint broke and i need to replace it. How do i take it off and put a new one in.(do i need a ball joint press) 98 Chevy Silverado 1500


jack up the the side with the broken ball joint under the control arm.
Remove the axle nut (4x4)
remove the caliper and the rotor.
remove the outer tie rod from the knuckle.
Remove the upper and lower control arm nuts and remove knuckle from vehicle.

Using a ball joint press remove and install the ball joint.

tighten axle nut (4x4 only) to 133 lb-ft after everything is assembled.

Nov 30, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

How to repair a lower ball joint on the passenger side


Hi.


jshreader_9.jpgjshreader_8.jpg

1. Raise and support vehicle.
2. Remove tire and wheel assembly, then install modified outer seal protector No. J34754, or equivalent, Fig.3 .
3. Remove lower ball joint cotter pin and nut, then loosen ball joint from steering knuckle using tool No. J-29330, or equivalent.
4. Position a suitable pry bar between suspension support and lower control arm and separate lower ball joint from steering knuckle. On some models, it may be necessary to remove nut attaching link to stabilizer shaft.
5. Locate center of rivet body and mark with a center punch.
6. Using a 1/8 inch drill, drill pilot holes completely through rivets. Using a 1/2 inch drill, drill final holes through rivets to ensure fitting of new ball joint.
7. Remove ball joint from lower control arm.
8. Assemble new ball joint to lower control arm with bolts provided in service package, Fig.9 . Tighten bolts to specifications.
9. Insert ball joint stud into steering knuckle and tighten nut to specifications, then install cotter pin.
10. Install wheel and tire and check front wheel alignment.

I hope this helps you.

Thanks.

Nov 28, 2010 | 1994 Pontiac Grand Prix

3 Answers

How many ball joints does a 99 dodge stratus have?


It has two,lower ball joints,one on each side.

Feb 11, 2010 | 1999 Dodge Stratus

1 Answer

How to replace lower left front ball joint ?


Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

  1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Tire and wheel
    • Wheel hub and bearing, if necessary
    • Outer tie rod retaining nut
    • Out tie rod from the steering knuckle using a suitable puller
    • Brake hose bracket retaining bolts and bracket
    • Upper control arm-to-steering knuckle pinch bolt and nut
    • Upper control arm from the steering knuckle
    • Lower ball joint retaining nut
    • Steering knuckle from the lower control arm using a suitable ball joint removal tool
    • Steering knuckle from the vehicle
    • Lower ball joint flange with a chisel
  4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
To install:
  1. Install or connect the following:
    • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
  2. Remove the tools from the lower control arm.
    • Tools J 9519-E and J 45105-1 to the lower ball joint
  3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
    • Steering knuckle to the lower control arm
    • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
    • Upper control arm to the steering knuckle
    • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
    • Brake hose bracket to the steering knuckle
    • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
    • Outer tie rod to the steering knuckle
    • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
    • Wheel hub and bearing, if removed
    • Tire and wheel
  4. Lower the vehicle
    • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
    • Wheel center cap, if removed
  5. Check the front wheel alignment.

Nov 30, 2009 | 2002 Oldsmobile Bravada

1 Answer

Need to replace the lower control Arm. Is there a procedure available?


Please be mindful to carefully note the position of the old parts as you disassemble the suspension, then follow these steps to do the re-installation:

REMOVAL

1. Disconnect the negative battery cable.

2. Raise and safely support the vehicle.

3. Remove the wheel and tire assembly.

4. Remove and discard the tension strut-to-control arm nut, then pull off the dished washer.

When separating the control arm from the steering knuckle, do not use a hammer. Be careful not to damage the ball joint boot seal.

5. Remove and discard the control arm-to-steering knuckle pinch bolt. Using a small prybar, spread the pinch joint slightly, then separate the control arm from the steering knuckle. A drift punch may be used to remove the bolt, but be very careful not to damage the ball joint boot seal.

Do not allow the halfshaft to move outward, or the tripod CV-joint internal parts could separate, causing failure of the joint.

6. Remove and discard the lower control arm inner pivot bolt and nut.

7. Remove the lower control arm from the frame and the tension strut.

INSTALLATION

Make sure the front washer is at the strut-to-lower control arm attachment.

8. Insert the strut into the inner bushing.

9. Position the lower control arm into the subframe bracket, using a new nut and bolt. Tighten to 73-97 ft. lbs. (98-132 Nm).

10. Assemble the lower control arm ball joint stud to the steering knuckle, making sure the ball stud groove is positioned properly. Be very careful not to damage the lower control arm seal.

11. Insert a new pinch bolt and nut, then tighten to 40-53 ft. lbs. (53-72 Nm).

12. Clean the strut threads to remove dirt and/or debris.

13. Install the dished washer, with its dished side away from the control arm bushing. Install a new nut on the strut and tighten to 73-97 ft. lbs. (98-132 Nm).

14. Install the wheel and tire assembly, tightening the lug nuts to 85-105 ft. lbs. (115-142 Nm), then carefully lower the vehicle.

I hope this helps.

Aug 17, 2009 | 1994 Ford Taurus

1 Answer

How to replace right front axle 2000 buick lesabre


Lift the passenger side of vehicle. Remove tire/wheel assembly. Remove the axle nut. Remove the tie rod end nut. Smack the side of the housing the tie rod end goes into to pop the tie rod end loose and out. Remove the sway bar link. Remove the lower ball joint nut. Smack the housing the lower ball joint goes into to pop the ball joint loose. Pry the lower control arm down to pop the ball joint out. swivel the rotor and strut assembly to the side. Pop the axle out. Reassemble in the reverse order.

Jul 05, 2009 | 2000 Buick LeSabre

1 Answer

2002 Honda Civic LX Front Lower Ball Joint Removal/Install.


I had a question i bought a used control arm for a 2001 honda civic compared it to the original and everything was the same except the part where the ball joint goes into is a few mm thicker on the control arm. Beedless to say i got it in but i had to over tighten to get the nut in all the way. I thought this would stop the rattling sound when i hit a pothole bit its still doing it and i fear the control arm is the incorrect one what other honda has the same control arm as the civic?

Jun 25, 2009 | 2002 Honda Civic

2 Answers

Ball Joint connecting lower control arm and spindle 99 Grand Prix


put a jack stand under the ball joint lower car, this applies pressure on the ball joint so the shaft of the ball joint does not turn.
heat the nut as well.

May 12, 2009 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...