Question about 1998 Honda CR-V

1 Answer

Slow speed vibration at 45 and above

Put brand new tires on replaced axle front left still vibrates

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 39 Answers

Maybe the tires need balanced?

Posted on Apr 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driving between 35-50 mile ph truck will start vibrating


There are many stages of vibration. The most common is in the steering and USUALLY a steering dampner will correct this. However, your description is not real defined and until the technician actually experiences it, it cannot be properly diagnosed

Aug 24, 2017 | Chevrolet Blazer Cars & Trucks

1 Answer

REAR passenger tire makes loud clunking and grinding noises when turning more than 30-45 degrees above 5-15 mph


I don`t think you have cv axles in the rear of that.My guess would be wheel bearings could be grinding. Donut spares are strickly to be used for short periods of time and not to be driven at any higher rates of speed. Some damage may have occurred during the actual incident when you had the flat initially.Damage to the rear axle itself,

Oct 12, 2012 | 1996 Dodge Caravan

1 Answer

Rotated & balanced tires. new driveshaft & center carrier bearing u-joints new shocks front & rear replaced rear axle bearings and seals new left rear rotor parking brake shoes new disc brake...


You will need to check things logically. Run the truck in the air and note where the vibration is at. Take the wheels OFF and put a few lug nuts to hold the rotors on, take the truck to 45mph or whatever the vibration is the worst. is it still there? if its gone, check wheels/ tires. if its still there, check rotors, axles. A drive shaft will make a rapid vibration at low speeds since it turns 3 to 4 times faster than the wheels. does it vibrate on or off the gas? Can you power through the vibration like go 60 and then coast back through? You have replaced a lot of parts that would not cause vibrations. Are you just changing parts willy nilly or is someone actually checking and verifying that these parts really bad?

Jul 18, 2011 | 2001 Chevrolet Silverado

1 Answer

The vehicle has a vibration felt in the seat and body of driver as the vehicle runs at high speeds. The problem seems to have started about the time I had new bushings put in the front stabilizer bar but...


Is it only at high speeds or all the time? At high speeds 60mph or above it could be the tire is not balanced properly. If it is felt all the time you could have a bent rim. If the tires are cupping it means you have faulty front end parts or the camber/ caster needs to be adjusted.

Dec 22, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Mycar has a vibration problem at 15 45 and 60 mph. even after new tires, alightment and balance.


you may have one of the cv-axle goes bad. jack one side of a time, put parking brakes on.
start the car and put in drive run up to speed and feel the vibration, the side has more vibration is the one that goes bad

Feb 28, 2010 | 2003 Cadillac CTS

1 Answer

2001 NISSAN QUEST VIBRATION


THE ORIGINAL VIBRATION MAY HAVE BEEN TIRES.IF THE LUG NUTS WERE NOT TORQUED BY HAND BUT OVERTIGHTED W/AN AIR RATCHET THE ROTORS MAY HAVE BEEN WARPED.TAKE IT BACK TO WERE THE TIRES WERE INSTALLED AND ASK THEM TO CHECK IT OUT.

Apr 30, 2009 | 2001 Nissan Quest

3 Answers

Subaru vibration


I had similar problem with my '99 outback. Replaced the front half shafts and seemed much better. A few months later seemed to be comming back so replaced the driver side shaft again and the problem disappeared. I had put in rebuilt shafts and the driver side shaft was not rebuilt correctly.

Feb 21, 2009 | 1999 Subaru Legacy

Not finding what you are looking for?
1998 Honda CR-V Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...