Question about 2008 Dodge Avenger

1 Answer

2008 dodge avenger serpentine belt diagram

We need a diagram for replacing the serpentine belt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Is it not on top of your radiator area, or underside of hood? What engine?

Posted on Apr 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
localwonder
  • 6784 Answers

SOURCE: diagram for a serpentine belt replacement for 2000 avenger dodge

HI. i have posted the diagram requested below.

7109f62.jpg

Posted on Aug 24, 2009

Testimonial: "This was exactly what we needed, Thank you so very much. "

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

c17hydro
  • 2984 Answers

SOURCE: 1998 Dodge Avenger serpentine belt issue

What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)

  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
  5. Connect the negative battery cable.

2.0 DOHC

Power Steering Pump And A/C Belt
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut.
  5. Connect the negative battery cable.

Posted on Oct 29, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

  • 31 Answers

SOURCE: i need a diagram of

There should be a diagram under your hood on the radiator support.

Hope this helps

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 avenger engine light won't go off after replacing serpentine belt


Belt has nothing to do with any OBD Code Check Lights,
it is just an accy drive belt

Check for codes & diagnose what ever area they take you to

Jul 18, 2012 | 2008 Dodge Avenger

1 Answer

Diagram to install serpentine belt on a 2008 dodge avenger


there is a sticker located at the front radiator frame on your vehicle that has that information

Jul 11, 2011 | Dodge Avenger Cars & Trucks

1 Answer

Wanna replace power steering pump on my 2008 dodge avenger and wanna know where the bolt is to loosen the tension belt


It's spring activated. Look for a pulley at the end of a lever. That's the tensioner pulley. Put a wrench/socket on it and move it away from the belt. Use caution, as I stated, it's spring loaded/activated. That's how it keeps constant pressure on the serpentine belt. Check under the hood for a routing diagram for re-installation. Or draw a quick sketch.

Hope this helped. I wasn't more precise, as I don't know which engine/options you have in it.

Mar 06, 2010 | 2008 Dodge Avenger

1 Answer

Putting serpentine belt back on


if you go to google.com and put in the year of your car and what you need, it will come up with a diagram.

Feb 18, 2010 | 2008 Dodge Avenger

1 Answer

I need a diagram for the serpentine belt without a/c on a 1996 dodge avenger


should be under the hood some where or in the owners Manuel if you havent looked in those places i would try that first

Jul 06, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

1,075 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...